Vertical SBX IP 320 Скачать руководство пользователя страница 56

Страница: 56 / 248

Call Handling

SBX IP 320 Features & Operation Guide

Forced Hands-free Mode

A DKTU caller can temporarily change the answering mode of the called party DKTU (tone
mode -> hands free mode).

Operation

To activate forced hands free mode, use the following procedure:

During a tone mode call to a DKTU, when you hear a ring back tone, dial the forced
hands free code number.

The called party DKTU will stop ringing and the speaker and microphone will be
activated (operate as hands free mode).

Conditions

•

If the DKTU is changed to hands-free mode, the connection tone will be provided and the
voice path is connected.

•

If the called party DKTU is set to linked-pair station, the answer mode of the called party
will be not changed.

•

If the calling party DKTU is set a linked-pair station, the calling party DKTU can use the
forced hands free mode.

•

If called party DKT is set as a Mobile-Ext, this feature will be not applied.

•

Only the calling party DKT that is designated in PGM 111 - 19 (with a setting of ON) can
use this feature.

•

After connection, related feature with hands free mode is not applied.(ex. call back)

Admin Programming

•

Forced Hands-Free Mode (PGM 111- FLEX 19)

Содержание SBX IP 320

























































































































































































































































Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды

Vertical SBX IP 320, Особенности и руководство по эксплуатации

Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды