Vertical SBX IP 320 Скачать руководство пользователя страница 173

Страница: 173 / 248

Rerouting

163

SBX IP 320 Features & Operation Guide

To deactivate Call Forward:

Lift the handset or press the [SPEAKER] button.

Press the [DND/FOR] button.

Press the # key (Call Forward cancel code).

Condition

•

To use Call Forward, a Station should be activated in Admin Programming.

Admin Programming

•

Allow Off-Net Call Forward (PGM 111 - FLEX 18)

•

Authorization Code Table (PGM 227)

Call Forward, Unconditional

A user forwards all calls immediately to another station, Hunt Group, or VMIB.

Operation

To activate Unconditional Call Forward:

Lift the Handset or press the [SPEAKER] button.

Press the [DND/FOR] button.

Dial the Call Forward code 1.

Dial Station or Group pilot number to receive the calls.

Replace the handset and go on-hook.

To assign {CALL FORWARD} button at a flexible button:

Press the [TRANS/PGM] button.

Press a flexible button.

Press the [DND/FOR] button.

Assign Call Forward type 1.

Dial the destination that will receive the call.

Press the [HOLD/SAVE] button to accept changes.

Содержание SBX IP 320

























































































































































































































































Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды

Vertical SBX IP 320, Особенности и руководство по эксплуатации

Результаты поиска

Содержание SBX IP 320

Отзывы:

Похожие инструкции для SBX IP 320

Бренды по названию

Популярные бренды