VALTIR QuadGuard HS Скачать руководство пользователя страница 19

Страница: 19 / 60

Valtir.com

Revision D November 2022

Important:

Because every impact is different, Valtir makes no

recommendation whether use or reuse of any part of the system is

appropriate or acceptable following an impact. It is the sole responsibility

of the project engineer and/or the local highway authority and its engineers

to make that determination. It is critical that you inspect this product after

assembly is complete to make certain that the instructions provided in this

manual have been strictly followed.

Miscellaneous

•

Traffic control equipment

•

Lifting and moving equipment (A lifting device is preferred although a forklift can be

used.) Minimum 5,000 lb. capacity required.

•

Air Compressor (100 psi minimum) and Generator (5 kW)

•

Long pry bar

•

Drift pin 12” [300 mm]

•

Center punch

•

Tape measure 25’ [7.5 m]

•

Chalk line

•

Concrete marking pencil

•

Steel bristle tube brush for cleaning 7/8” drilled holes

•

Rags, water, and solvent for touch-up

Note

The above list of tools is a general recommendation. Depending on specific site

conditions and the complexity of the assembly specified by the appropriate highway

authority, additional or fewer tools may be required. Decisions as to what tools are needed

to perform the job are entirely within the discretion of the specifying highway authority

and the authority’s selected contractor performing the assembly of the system at the

authority’s specified site.

Содержание QuadGuard HS





























































Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды

VALTIR QuadGuard HS, Инструкция по сборке

Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды