VALTIR QuadGuard HS Скачать руководство пользователя страница 44

Страница: 44 / 60

Valtir.com

Revision D November 2022

3) Attach Side Panels and/or Transition Panels to Backup Assembly

A. Attach Hinge Plate to the Transition Panel or Side Panel using 5/8” rail bolts and

5/8” rail nuts (two places – top and bottom holes only).

B. Attach Transition Panel or Side Panel assembly to side of Backup using 5/8” hex

bolt, 5/8” lock washer and 5/8” hex nut three places each side of Backup (Figure

53).

C. Attach diagonal brace to Fender Panel and Backup using 3/8” hex bolt, 3/8” lock

washer and 3/8” hex nut (two places per brace; four places per side).

D. Secure each diagonal brace with 3/8” hex bolt, 3/8” lock washer and 3/8” hex nut

(two places per brace) as shown in Figure 53.

Note:

A Side Panel is not needed when a Transition Panel is used. Refer to the drawing package

as Diagonal Braces are not used with some Transition Panels.

Assembly tip:

Use drift pin to align the center hole of the Panel with the center hole of the Backup

before attaching the rail bolts.

Figure 53

Side Panel/Transition Panel Attachment

DIAGONAL BRACE (INNER)

5/8” X 4” HEX BOLT

5/8” LOCK WASHER

5/8” HEX NUT (SMALL)

5/8” RAIL NUT (LARGE)

HINGE PLATE

3/8” LOCK WASHER

3/8” HEX NUT

5/8” RAIL BOLT

WIDE SIDE PANEL

3/8” X 3 1/2”

HEX BOLT

DIAGNOAL BRACE (OUTER)

3/8” HEX NUT

3/8” LOCK WASHER

3/8” X 3 1/2” HEX BOLT

TENSION STRUT BACKUP

Содержание QuadGuard HS





























































Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды

VALTIR QuadGuard HS, Инструкция по сборке

Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды