VALTIR QuadGuard HS Скачать руководство пользователя страница 2

Страница: 2 / 60

QuadGuard

is a registered trademark of Valtir, LLC.

Part No. 115310

Valtir.com

Revision D November 2022

QuadGuard

The QuadGuard

system has been tested pursuant to National Cooperative Highway Research

Program (“NCHRP”) Report 350 specifications. The QuadGuard

HS system has been deemed

eligible for Federal-aid reimbursement on the National Highway System by the Federal Highway

Administration (“FHWA”).

Assembly Manual

15601 Dallas Parkway

Suite 525

Addison, Texas 75001

Warning:

The local highway authority, distributors, owners, contractors,

lessors, and lessees are

RESPONSIBLE

for the assembly, maintenance, and

repair of the QuadGuard

HS. Failure to fulfill these

RESPONSIBILITIES

with

respect to the assembly, maintenance, and repair of the QuadGuard

could result in serious injury or death.

Important:

These instructions are for standard assembly specified

by the appropriate highway authority. In the event the specified system assembly,

maintenance, or repair would result in a deviation from these assembly

instructions, contact the appropriate highway authority engineer.

This manual must be available to the worker overseeing and/or assembling the product at

all times. For additional copies, contact Valtir directly at (888) 323-6374 or visit

Valtir.com/Products/

The information contained in this manual supersede all previous versions. The instructions,

illustrations, and specifications are based on the latest QuadGuard

information available to

Valtir at publication. We reserve the right to make changes at any time. Please visit

Valtir.com/Product/QuadGuard-HS/

to confirm the latest revision.

Содержание QuadGuard HS





























































Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды

VALTIR QuadGuard HS, Инструкция по сборке

Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды