VALTIR QuadGuard HS Скачать руководство пользователя страница 6

Страница: 6 / 60

Valtir.com

Revision D November 2022

Limitations and Warnings

Valtir, in compliance with NCHRP Report 350, contracts with FHWA approved testing facilities to

perform crash tests, evaluation of tests, and submit results to the FHWA for review.
The QuadGuard

HS system has been deemed eligible for reimbursement by FHWA as meeting

the requirements and guidelines of NCHRP Report 350 TL-3 Plus with an increase speed from

62 mph [100 km/h] to 70 mph [113 km/h]. These tests typically evaluate product performance by

conducting testing pursuant to parameters set forth in NCHRP Report 350 and accepted by

FHWA which include a range of vehicles from lightweight cars (approx. 1800 lb. [820kg]) to full

size pickup trucks (approx. 4400 lb. [2000 kg]) as specified by the FHWA. A product can be

certified for multiple Test Levels. The QuadGuard

HS is certified to the Test Level(s) as shown

below:

Test Level 3 Plus: 70 mph [113 km/h]

These FHWA directed tests are not intended to represent the performance of systems

when impacted by every vehicle type or every impact condition existing on the roadway.

This system is tested only to the test matrix criteria of NCHRP Report 350 as approved by

FHWA.

Valtir expressly disclaims any warranty or liability for injury or damage to persons or property

resulting from any impact, collision or harmful contact with products, other vehicles, or nearby

hazards or objects by any vehicle, object or person, whether or not the products were assembled

in consultation with Valtir or by third parties.
The QuadGuard

HS is intended to be assembled, delineated, and maintained within specific

state and federal guidelines. It is important for the highway authority specifying the use of a

highway product to select the most appropriate product configuration for its site specifications.

The customer should be careful to properly select, assemble, and maintain the product. Careful

evaluation of the site lay out, vehicle population type; speed, traffic direction, and visibility are

some of the elements that require evaluation in the selection of a highway product. For example,

curbs could cause an untested effect on an impacting vehicle.
After an impact occurs, the debris from the impact should be removed from the area immediately

and the specified highway product should be evaluated and restored to its original specified

condition or replaced as the highway authority determines as soon as possible.

Warning:

Do not assemble, maintain, or repair the QuadGuard

HS until you

have read this manual thoroughly and completely understand it. Ensure that all

Danger, Warning, Caution, and Important statements within the manual are

completely followed. Please call Valtir at (888) 323-6374 if you do not understand

these instructions.

Warning:

Ensure that all of the QuadGuard

HS Danger, Warning, Caution, and

Important statements within the QuadGuard

HS manual are completely followed.

Failure to follow this warning could result in serious injury or death in the event of

a collision.

Содержание QuadGuard HS





























































Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды

VALTIR QuadGuard HS, Инструкция по сборке

Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды