VALTIR QuadGuard HS Скачать руководство пользователя страница 7

Страница: 7 / 60

Valtir.com

Revision D November 2022

System Overview

The QuadGuard

HS, through crash testing, has been shown to be a potentially reusable, re-

directive, non-gating crash cushion, within NCHRP Report 350 criteria, for hazards ranging in

width from 24” to 90” [610 mm to 2285 mm]. It consists of energy-absorbing cartridges surrounded

by a framework of Quad-Beam

Panels.

Important:

Valtir makes no recommendation whether use or reuse of any

part of the system is appropriate or acceptable following an impact. It is the

sole responsibility of the project engineer and/or the local highway authority

and its engineers to make that determination. It is critical that you inspect

this product after assembly is complete to make certain that the instructions

provided in this manual have been strictly followed.

The QuadGuard

HS system utilizes two types of cartridges in a “staged” configuration and empty

Bays to address both lighter cars and heavier, high center-of-gravity vehicles.

Impact Performance

The 9 Bay QuadGuard

HS systems have successfully passed the requirements stipulated in

NCHRP Report 350, Test Level 3 tests with both the light car and pickup at speeds of 70 mph

[113 km/h] at angles up to 20 degrees.
During head-on impacts, within NCHRP Report 350 criteria, the QuadGuard

HS has been shown

that it compresses rearward and crushes to absorb the energy of impact. When impacted from

the side, it safely redirects the vehicle back toward its original travel path and away from the

hazard.

Inspect Shipping

Before deploying the

QuadGuard

, check the received parts against the shipping list supplied

with the system to ensure all parts are included.

Important:

The Manufacturer’s Drawing Package supplied with the

QuadGuard

must be used with these instructions for proper assembly and should take

precedence over these general instructions.

Warning:

Do NOT modify the QuadGuard

HS in any way.

Содержание QuadGuard HS





























































Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды

VALTIR QuadGuard HS, Инструкция по сборке

Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды