VALTIR QuadGuard HS Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 60

background image

31

Revision D November 2022

7) Attach Fender Panels

Note:

Do not mix the 5/8” rail nuts (large) with the 5/8” hex nuts (small) (Figure 27).

Starting at the Backup, attach left and right Fender Panels (Figure 28).
Attach the front of the Fender Panels to the next diaphragm using two rail bolts and large

rail nuts per side. Use only the top and bottom holes; leave the center hole open until the

next Fender Panel is attached.
Attach Mushroom Washer Assembly as shown in Figure 28 and 29, but do not torque at

this time.
After the first set of Fender Panels is attached to the third diaphragm from the front, attach

Bumper Assembly for Diaphragm 3. Attach next set of Fender Panels and attach Bumper

Assembly for Diaphragm 2. Repeat for Diaphragm 1 (Step 8 – “Attach Bumper Assembly”).

Figure 27

(Rail Nuts are Over Sized)

Figure 28

Fender Panel Assembly

5/8” HEX NUT (SMALL)

5/8” HEX NUT (LARGE)

24 mm [15/16”]

24 mm [1 1/4”]

«
...
30
31
32
33
34
...
»

Содержание QuadGuard HS





























































Отзывы:

Нет отзывов

Похожие инструкции для QuadGuard HS

Бренд: GE Страницы: 425

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: 2N Страницы: 91

Бренд: RAM Страницы: 32

Бренд: Rain Bird Страницы: 20

Бренд: VAT Страницы: 39

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренд: Taoglas Страницы: 2

Бренд: Sunnen Страницы: 24

Бренд: Jäger Страницы: 18

MT600iWP Series

Бренд: weintek Страницы: 2

Бренд: Zencontrol Страницы: 2

Бренд: Gasboy Страницы: 119

Бренд: MERCATOR Страницы: 4

Бренд: W&T Страницы: 217

Бренд: HANYOUNG NUX Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды