VALTIR QuadGuard HS Скачать руководство пользователя страница 14

Страница: 14 / 60

Valtir.com

Revision D November 2022

The QuadGuard

HS system may be installed on any of the following foundations using the

specified anchorage:

Foundation D: Asphalt Only

Foundation: 8” [200 mm] minimum A.C.
Anchorage:

Approved adhesive with

18” [460 mm] studs - 16 1/2” [420 mm] embedment

Important:

Systems mounted on asphalt must be replaced and mounted on

fresh, undisturbed asphalt if more than 10% of anchors are found to be loose,

broken, or show signs of pull out. If 10% or fewer anchors are damaged, replace

the damaged anchors in the existing asphalt. Anchor bolts used on systems

mounted on asphalt must be inspected every 6 months.

See Post Impact

Instructions and Maintenance and Repair instructions on page 54.

Foundation A: Concrete Pad or Roadway

Foundation: 150 mm [6”] minimum depth Portland Cement Concrete (P.C.C.)
Anchorage:

Approved adhesive

with 180

mm [7”] studs 140 mm [5 1/2”] embedment

Foundation B: Asphalt over P.C.C.

Foundation: 76 mm [3”] minimum asphalt concrete (A.C.) over 76 mm [3”] minimum P.C.C.
Anchorage: Length of anchor required is 460 mm [18”] 420 mm [16 1/2”] embedment

Foundation C: Asphalt over Compacted Subbase (C.S.)

Foundation: 150 mm [6"] minimum A.C. over 150 mm [6”] minimum C.S.
Anchorage:

Approved adhesive with 460

mm [18"] studs 420 mm [16 1/2”] embedment

Foundation Specifications

For Foundations A, B, C and D mentioned above:

A. C. (Asphalt Concrete)

AR-4000 A. C. (per ASTM D3381 '83) 3/4” Maximum, Medium (Type A or B) aggregate

Caution:

Walk-up inspections are recommended at least once every six

months for installations on asphalt.

Содержание QuadGuard HS





























































Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды

VALTIR QuadGuard HS, Инструкция по сборке

Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды