VALTIR QuadGuard HS Скачать руководство пользователя страница 5

Страница: 5 / 60

Valtir.com

Revision D November 2022

Safety Symbols

This section describes the safety symbols that appear in this QuadGuard

HS manual. Read the

manual for complete safety and assembly information.

Symbol

Meaning

Safety Alert Symbol:

Indicates Important, Caution, Warning, or Danger. Failure

to read and follow the Important, Caution, Warning, or Danger indicators could

result in serious injury or death to the workers and/or bystanders.

Warning:

Read safety instructions thoroughly and follow the assembly directions

and suggested safe practices before assembling, maintaining, or repairing the

QuadGuard

HS. Failure to comply with these warnings could result in increased

risk of serious injury or death in the event of a vehicle impact with a system.

Important:

Please keep up-to-date instructions for later use and reference by

anyone involved in the assembly of the product.

Safety Rules for Assembly

* Important Safety Instructions *

This manual must be kept in a location where it is readily available to persons who are skilled and

experienced in the assembly, maintenance, or repair of the QuadGuard

HS system. Additional

copies of this manual are available from Valtir by calling (888) 323-6374 or visiting

Valtir.com/Product/QuadGuard-HS/

. Please contact Valtir if you have any questions concerning

the information in this manual or about the QuadGuard

HS.

Always use appropriate safety precautions when operating power equipment, mixing chemicals,

and when moving heavy equipment or QuadGuard

HS components. Safety articles including

but not necessarily limited to work gloves, eye/ear protection, safety-toe shoes, silica dust

management systems, and back protection should be used.

Warning:

It is the responsibility of the installer to use all safety measures

incorporating appropriate traffic control devices specified by the highway authority

must be used to protect all personnel while at the assembly, maintenance, or repair

site.

Warning:

It is the responsibility of the installer to ensure that your assembly

procedure meets all appropriate Occupational Safety and Health Administration

(OSHA) and local standards

Содержание QuadGuard HS





























































Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды

VALTIR QuadGuard HS, Инструкция по сборке

Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды