VALTIR QuadGuard HS Скачать руководство пользователя страница 48

Страница: 48 / 60

Revision D November 2022

8) Attach Fender Panels

Starting at the last Bay, attach left and right Fender Panels as shown in Figure 62. Attach

the Hinge Plate at the front of the Fender Panels to the Diaphragm in front using three

5/8” hex bolts, nuts, and washers.
Attach Mushroom Washer assembly as shown in Figure 62, Detail A, and Detail B; do not

torque at this time.

Mushroom Washer must lay flat against the

Fender Panel as shown in Detail B. Standoff on

washer must be fully seated through slot.

Detail B

Mushroom Washer Orientation

Detail A

Mushroom Washer Assembly

Figure 61

Fender Panel Assembly

6” DIE SPRING

5/8” RAIL NUT (LARGE)

MUSHROOM WASHER

TENSION STRUT BACKUP

5/8X8 1/2”, G8
FLATHEAD SOCKET SCREW

FENDER PANEL

5/8” LOCK WASHER

5/8” HEX NUT (SMALL)

5/8X4” G5 HEX BOLT

5/8” RAIL NUT (LARGE)

6” DIE SPRING

DIAPHRAGM

OR BACKUP

17.5 mm [11/16”]

ROUND HOLE

QUAD-BEAM™

FENDER PANEL

MUSHROOM WASHER

HINGE PLATE

PANEL ALREADY ATTACHED

TO DIAPHRAGM OR BACKUP

LONG SLOT IN

FENDER PANEL

Содержание QuadGuard HS





























































Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды

VALTIR QuadGuard HS, Инструкция по сборке

Результаты поиска

Содержание QuadGuard HS

Отзывы:

Похожие инструкции для QuadGuard HS

Бренды по названию

Популярные бренды