Valco Cincinnati VC350A Скачать руководство пользователя страница 77

Страница: 77 / 327

Section 10

—

Troubleshooting

VC350A Flexoseal

System

Valco Cincinnati

10-7

Problem

Possible Cause

Possible Solution

Glue Problems

Glue drips or runs from
applicator head when
the parent machine is
stopped.

1a. Dirty glue valve

1b. Defective glue valve

1c. Defective solenoid seal

1d. Defective main board

1e. Glue flow knob is not adjusted

correctly.

1a. Clean the valve

1b. Repair or replace glue valve

1c. Replace the solenoid air valve.

1d. Defective main board

1e. Using glue flow knob, decrease

pressure.

Glue drips or runs from
applicator head when
the parent machine is
operating.

2a. Incorrect lateral adjustment

2b. Incorrect angle of applicator head

2c. Incorrect applicator head

2a. Reposition applicator head.

2b. Adjust applicator head to 35°.

2c. Replace applicator head.

Excessive glue is
present on the product.

3a. Glue pattern is too long

3b. Applicator assembly is in the

wrong position

3c. Incorrect applicator head

3d. Glue pressure is too high

3e. Box tab is cut too small

3f. Glue viscosity too low

3a. Adjust the pattern length.

3b. Adjust the position of the

assembly.

3c. Replace the applicator head.

3d. Decrease glue pressure.

3e. Adjust the cutter position.

3f. Use glue with 1500-2000 cps

viscosity.

Glue is leaking from the
solenoid air valve.

4a. Defective glue valve diaphragm

4a. Rebuild or replace glue valve.

Boxes are not sealing.

5a. Too much or not enough glue is

being applied

5a. Adjust the glue flow

Glue-regulator pressure
increases while the
parent machine is idle.

6a. Regulator is not seating

6a. Remove the large nut from the

bottom of the pressure regulator.
Remove the ball and spring.
Inspect, clean or replace as
necessary. (Use Valco’s regulator
repair kit 563xx038.)

Glue valve activates at
random.

7a. Scanner is detecting material other

than the product (scrap board or
machine parts)

7b. Scanner is not detecting either the

print or the dark colors.

7c. Shaft encoder timing belt is loose

7d. Defective circuit cards

7a. Adjust scanner position (cell-to-

gun dimension must be
recalculated if scanner is moved).

7b. Lower scanner or change to a

different type of scanner.

7c. Tighten or replace belt.

7d. Check and replace cards.

Содержание VC350A








































































































































































































































































































































Результаты поиска

Содержание VC350A

Отзывы:

Похожие инструкции для VC350A

Бренды по названию

Популярные бренды

Valco Cincinnati VC350A, Руководство пользователя

Результаты поиска

Содержание VC350A

Отзывы:

Похожие инструкции для VC350A

Бренды по названию

Популярные бренды