Valco Cincinnati VC350A Скачать руководство пользователя страница 72

Страница: 72 / 327

Section 10

—

Troubleshooting

VC350A Flexoseal

System

Valco Cincinnati

10-2

Problem

Possible Cause

Possible Solution

Glue Pattern, continued

There is an interruption
of the glue pattern on
the perforation of the
product.

6a. Glue pattern is too close to the

perforation

6a. Shorten the glue pattern.

Glue pattern is poor.

7a. Air bubbles are present in the glue

system.

Run adhesive through the glue
line to purge air from the system

Flush system

The glue pattern begins
thick, but then trails off.

8a. Angle of the applicator head is too

steep.

8b. Air pressure to the 3-way valve is

too high.

8a. Adjust angle to 35 degrees.

8b. Lower the air pressure to 25 psi

(2.7 bar) higher than the highest
operating glue pressure.

The glue pattern begins
normally, but then trails
off.

9a. Angle of the applicator head is not

steep enough.

9b. There is a worn O-ring in the

swivel fitting.

9a. Adjust angle to 35 degrees.

9b. Replace O-ring.

10. The glue pattern

consists of drops of glue
with trailing.

10a. Contact between the product and

the spring guide is poor.

10a.

Increase the tension of the
spring.

11. There are differences in

glue stripes.

11a. The glue lap crusher setting too

narrow.

11a.

The glue station is not in line
with the product.

12. Good pattern with

trailing.

12a. Glue pressure is too high.

12a.

Ensure that the pressure is 10-
15 psi (1.7-2 bar).

13. Trailing (glue pattern is

applied past the point of
desired shutoff).

13a. Shutoff point not set correctly

13b. Air is present in glue lines

13c. Applicator head O-ring is

missing or worn

13d. Dirty solenoid air valve

13a.

Adjust front-panel switches.

13b. Purge air from glue lines.

13c.

Replace O-ring

13d. Clean the solenoid air valve.

14. Good pattern position at

slow parent machine
speed. Delayed pattern
at higher speed.

14a. Glue may be present in the air

solenoid valve.

14a.

Change air solenoid. Reset
settings.

15. Good pattern at slow

parent machine speed;
thin pattern (not enough
glue) at higher speed.

15a. Insufficient glue pressure.

15a.

Increase glue pressure, using
the glue pressure knob on the
front panel of the VC350A.

Содержание VC350A








































































































































































































































































































































Результаты поиска

Содержание VC350A

Отзывы:

Похожие инструкции для VC350A

Бренды по названию

Популярные бренды

Valco Cincinnati VC350A, Руководство пользователя

Результаты поиска

Содержание VC350A

Отзывы:

Похожие инструкции для VC350A

Бренды по названию

Популярные бренды