Valco Cincinnati VC350A Скачать руководство пользователя страница 255 | Manualshive

Страница: 255 / 327

background image

7-2

Valco Cincinnati, Inc.

Section 7 - Initial Setup

MC060 Manual/VC350AG AutoGlue Control System

5.

Next, with the parent machine stopped and the VC350AG
control powered on, adjust the “ZERO” pot on the EPC board
(151xx430). Turn the pot using a small screwdriver so that the
pressure gauge on the control is set to 15 psi for the air actuated
valves and 20 psi if you are using the electric actuated valves.

6.

Move the arrow handle on the top of the Fluid Balancing
Regulator towards the “EPC” setting, as marked on the top of
the regulator.

7.

Verify that the adhesive line is connected to the input port of the
Fluid Balancing Regulator and an output line runs to the glue
valve.

8.

The pressure on the Fluid Balancing Regulator gauge and the
VC350AG EPC gauge should read approximately the same.
This is the purge pressure.

9.

Adjust the flow control knob on the front of the VC350AG to the
12 o’clock position and run the parent machine up to the normal
operating speed.

10. Both pressure gauges should increase as the machine speed

increases.

11. With the parent machine running at normal speed, find the

“SPAN” pot on the EPC board (151xx430) in the VC350AG
control. Adjust this pot using a small screwdriver until the
maximum glue pressure is shown on the glue pressure gauge.

12. The Fluid Balancing Regulator will work in the event that the

EPC should fail. If this should happen, turn the arrow handle on
the Balancing Regulator so that it points to the “PURGE” label.

13. Adjust the pressure manually by turning the round black knob on

the small air regulator located on top of the Fluid Pressure
Regulator. This will maintain a current pressure at all machine
speeds.

Table 7-1. Air Pressure Settings—Minimum Input Pressure at Machine Idle

Air Pressure Settings

Component

Contact Extrusion

Non-Contact Extrusion

Pressurized tank

60 psi / 5.1 bar

70-120 psi / 5.8-9.2 bar

DD-1 pump

80 psi / 6.5 bar

80 psi / 6.5 bar

2:1 ratio pump

80 psi / 6.5 bar

80 psi / 6.5 bar

5:1 ratio pump

40 psi / 3.7 bar

40 psi / 3.7 bar

Fluid flow control (EPC) 80 psi / 6.5 bar

60-80 psi / 5.1-6.5 bar

Glue valves

80 psi / 6.5 bar

Not applicable

Glue Delivery System (w/ 1:1 fluid
balancing regulator) - Continued

«
...
253
254
255
256
257
...
»

Содержание VC350A








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC350A

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: Laica Страницы: 4

Бренд: Taber Страницы: 27

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: Caframo Страницы: 72

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренд: V-TEK Страницы: 112

The Wave Transformer

Бренд: EarthQuaker Devices Страницы: 21

Бренд: M-system Страницы: 3

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды