Valco Cincinnati VC350A Скачать руководство пользователя страница 67

Страница: 67 / 327

Section 9

—

Maintenance

VC350A Flexoseal

System

Valco Cincinnati

9-8

Repairing the Fluid Regulator

Disassembly

To repair the fluid regulator (Figure 9-4), follow these steps:

1. Reduce pressure in inlet and outlet lines to zero.

2. Turn the “T” handle (1) counterclockwise until all of the load is removed from the

spring (6).

Note!

The regulator can be disassembled without removal from the glue line.

3. Remove the bonnet screws (4), bonnet (3), upper spring rest (5), spring (6), lower spring rest (7), dia-

phragm (8), and diaphragm protector (9).

4. Lift out the valve pin (10) and unscrew the valve seat (11), using a 7/8" socket wrench.

5. Remove the bottom plug (17), gasket (16), spring (15), ball seat (14), and ball valve (13).

Reassembly

To reassemble the fluid regulator, follow these steps:

1. Reassemble parts in reverse order of disassembly.

2. Apply a small amount of lithium grease or equivalent evenly to the full length of the threads and tip of the

“T” handle (1).

3. Torque the bonnet screws (4) to 60 inch-pounds.

Содержание VC350A








































































































































































































































































































































Результаты поиска

Содержание VC350A

Отзывы:

Похожие инструкции для VC350A

Бренды по названию

Популярные бренды

Valco Cincinnati VC350A, Руководство пользователя

Результаты поиска

Содержание VC350A

Отзывы:

Похожие инструкции для VC350A

Бренды по названию

Популярные бренды