Uponor AquaSAFE Скачать руководство пользователя страница 58

Страница: 58 / 72

To multipurpose
sprinkler system

Softner/filter outlet
control valve

Water softener/
filtration system

Softener/filter inlet
control valve

PRV

Set PRV to

psi

per
design

Flow switch with gauge
assembly for potable
systems (optional)

Pressure gauge
At least one installed
downstream of the
pressure-reducing
valve (PRV)

PRV set pressure
This pressure requirement
is different on every project.
See design plans for actual
PRV set pressure.

Softener/filter outlet tee

To water heater

Softener/filter inlet tee

Tee to hard-water
fixtures

Main shutoff valve(s)

Main supply

• Water flows through
softener during normal
domestic use

• Pressure drop from
sprinkler operation
opens PRV

• Allows flow through PRV

• Flow switch can provide

alarm, if required

Figure 9-1: Domestic water bypass installation with optional flow switch

Installation guidelines

Refer to Figure 9-1 and use the following steps to install a

domestic water bypass.
1. Install the domestic water bypass line. There needs to be

a straight line from the main shutoff valve

to the PRV

and also from the PRV to the softener/filter outlet tee

This will ensure proper operation of the fire sprinkler system.

If additional 90-degree elbows are installed on the piping

through the PRV, contact Uponor Construction Services to

recalculate the system.

Visit:

uponor-usa.com/construction-services

Email:

[email protected]

U .S .

: 800.321.4739,

Canada

: 888.594.7726

52 l Uponor AquaSAFE System Installation Guide

Содержание AquaSAFE









































































Результаты поиска

Содержание AquaSAFE

Отзывы:

Похожие инструкции для AquaSAFE

Бренды по названию

Популярные бренды

Uponor AquaSAFE, Руководство по установке

Результаты поиска

Содержание AquaSAFE

Отзывы:

Похожие инструкции для AquaSAFE

Бренды по названию

Популярные бренды