manualshive.com logo in svg

Uponor AquaSAFE, Руководство по установке, Страница: 9 / 72

Поделиться
Скачать
Uponor AquaSAFE Скачать руководство пользователя страница 9

• Uponor AquaPEX piping shall not be installed in locations with 

direct exposure to sunlight. 

• Piping shall be supported every 24" with metal pipe hangers 

designed for use with non-metallic pipe/

piping. Follow  

minimum bend radius limitations as detailed on page 26 of 

this installation guide. Drilling through joists is an acceptable 

method of support if allowed by the AHJ, joist manufacturer, 

and applicable building codes.

Exposed finished ceiling assemblies
• Ceiling shall be horizontal and must be finished with minimum 

33

⁄

88

"-thickness gypsum wallboard, a suspended membrane 

ceiling with lay-in panels or tiles having a minimum weight  

of 0.35 lf/ft

2

 installed with metallic support grids, or ½"-thick, 

code-complying plywood or solid sheathing.

• Piping shall be supported every 24" with metal supports 

designed for use with non-metallic pipe/piping. Follow 

minimum bend radius limitations as detailed on page 26 of 

this installation guide. Drilling through joists is an acceptable 

method of support if allowed by the AHJ, joist manufacturer, 

and applicable building codes.

• Listed residential sprinklers with an activation temperature of 

155°F (68.3°C) and 4.9 minimum K-factor shall be used in the 

exposed portion of the sprinkler system. Sprinkler spacing shall 

be no larger than 16 ft. Per NFPA 13D, sprinklers shall be ins

talled 

with deflectors no more than 1¾" below the bottom of the joist 

to account for future finished ceilings.

 

uponor-usa.com

  |  

uponor.ca

  l  3

Содержание AquaSAFE









































































Отзывы:

Нет отзывов