Uponor AquaSAFE Скачать руководство пользователя страница 11

Страница: 11 / 72

• Do not solder within 18" of any PEX piping in the same water

line. Make all sweat connections prior to making the fitting

connection.

• Do not install PEX piping between the tub/shower valve and

tub spout.

• Do not use PEX piping for an electrical ground.
• Do not spray on or allow any organic chemicals, pesticides,

strong acids or strong bases to be exposed to PEX piping.

• Do not use petroleum or solvent-based paints on PEX piping.
• Use only approved and appropriate firestop materials with

PEX piping. Verify firestop compatibility with the firestop

manufacturer.

• Although PEX piping does not attract rodents, pests, and other

insects, these uninvited guests can have detrimental effects on

PEX system integrity as well as duct systems, electrical systems,

and other integrated systems in a home. Property owners should

take steps to eliminate pests.

• Do not subject PEX piping to impact.
• During remodeling or ceiling repair, take appropriate

precautions to protect the piping and sprinklers from damage.

• Do not install PEX piping and ProPEX fittings in combustible,

concealed spaces where sprinklers are required by NFPA 13D

standard and the National Building Code of Canada

(as applicable).

Uponor AquaSAFE multipurpose fire sprinkler

system overview

The AquaSAFE system is a cost-effective way to provide reliable

and safe home fire protection. This progressive technology

combines the plumbing and fire sprinkler systems into an

efficient, cost-effective, multipurpose system featuring

dependable Uponor AquaPEX piping.
Uponor AquaSAFE systems are available in various system

layouts. Figure 2-1 on

page 14

depicts a looped system

configuration.

uponor-usa.com

uponor.ca

l 5

Содержание AquaSAFE









































































Результаты поиска

Содержание AquaSAFE

Отзывы:

Похожие инструкции для AquaSAFE

Бренды по названию

Популярные бренды

Uponor AquaSAFE, Руководство по установке

Результаты поиска

Содержание AquaSAFE

Отзывы:

Похожие инструкции для AquaSAFE

Бренды по названию

Популярные бренды