Uponor AquaSAFE Скачать руководство пользователя страница 25

Страница: 25 / 72

Chapter 4

Installing sprinkler adapters

The design printout shows sprinkler placement and spacing.

The number after the dash indicates proper sprinkler spacing

(in square feet).
Example: RC-RES-16 signifies a concealed 4.9k sprinkler,

designed to cover a 16' x 16' area. The maximum distance off

any wall is equal to half the distance of the maximum spacing

selected. For example, if the design dictates that the sprinklers

are spaced 16' apart, do not place farther than 8 ft. off the wall.

Installation instructions

1. The design printout should list the type of sprinkler to use in

your installation.

2. Use the sprinkler design printout to determine the proper

location for installing the sprinkler adapters.

Caution: Avoid obstructions that may interfere

with sprinkler discharge when mounting sprinkler

assemblies. Anticipate the use of fans, surface-

mounted lighting, beams and slopes. For specific clearance

requirements, refer to NFPA 13D. Vaulted ceilings and

obstructions added after the system design is completed

can interfere with proper sprinkler operation.

Contact Uponor Construction Services at

design.services@

uponor.com

if ceiling vaults or beams are not shown on the

sprinkler plan.

Note: The sprinkler plan will identify the most hydraulically

remote sprinkler(s) that will be used for flow-verification

testing. To save time during that procedure, make sure these

sprinkler locations are clearly defined during installation.

3. Attach the sprinkler-mounting bracket or sprinkler adapter to

the structure with two #10 x 1½" coarse-thread screws. If using

the lower set of mounting holes, install a third screw in the

center hole of the bracket. Refer to the sprinkler plan mounting

details for correct placement of brackets and adapters, paying

close attention to the ceiling type and sprinkler model.

uponor-usa.com

uponor.ca

l 19

Содержание AquaSAFE









































































Результаты поиска

Содержание AquaSAFE

Отзывы:

Похожие инструкции для AquaSAFE

Бренды по названию

Популярные бренды

Uponor AquaSAFE, Руководство по установке

Результаты поиска

Содержание AquaSAFE

Отзывы:

Похожие инструкции для AquaSAFE

Бренды по названию

Популярные бренды