Uponor AquaSAFE Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 72

Uponor AquaSAFE Скачать руководство пользователя страница 19

Chapter 2

Design

Sprinkler plans

Uponor can provide a sprinkler layout design plan and engineer-

stamped drawings. Uponor designers use hydraulic calculation

software to create system layouts that provide reliable fire

sprinkler protection. This software specifies the proper sprinkler

locations, necessary flow rates and pressures. The resulting

designs comply with nationally recognized fire codes and

standards and meet the requirements of the NFPA 13D standard

and the National Building Code of Canada (as applicable).
For information about integrating Uponor AquaSAFE

details into existing sprinkler design software, certified

designers can contact Uponor Construction Services at

[email protected]

.

Design information

Uponor’s design provides the following information:
• Model — Type of sprinkler used
• Nominal orifice size — Size of the orifice on the sprinkler
• Temperature rating — Temperature the sprinkler will activate
• K factor — A number that describes the size of the hole

available for water flow through the sprinkler

• Maximum sprinkler spacing — Maximum spacing between

the sprinklers (determined by the designer and indicated for

each sprinkler on the layout)

• Maximum distance to wall — The maximum distance the

sprinkler may be placed from the wall (equal to half the

maximum sprinkler spacing designated on the layout)

• Single sprinkler — When performing a single-sprinkler flow

verification test, the pressure and flow requirements for

that sprinkler at various spacing

• Two or more sprinklers — When performing a flow verification

test for two or more sprinklers, the pressure and flow

requirements for those sprinklers at the selected spacing

uponor-usa.com

|

uponor.ca

l 13

«
...
17
18
19
20
21
...
»

Содержание AquaSAFE









































































Отзывы:

Нет отзывов