Trine 4100 Electric Strike Скачать руководство пользователя страница 9

Страница: 9 / 65

You should NOT see the "X" on top of the actuator cam.

Use the plunger and

RED colored solenoid

spring assembly.

Fail Secure

You should have the "X" mark on top of the actuator cam.

Use the plunger and

BLUE colored solenoid

spring assembly.

DO NOT OPEN

THIS SIDE.

TROUBLESHOOTING THE COMPLETED INSTALLATION:

Seat wires properly in

the housing channel so

the cover will seat flat.

INSTRUCTIONS FOR CHANGING THE THE 4850 FROM FAIL SECURE

TO FAIL SAFE:

To change the Fail Secure 4850 into a Fail Safe, open the

mechanism side of the strike (as shown on the right) by removing

the mechanism cover screws (3 places) and the cover. Lift the solenoid

and gently pull off the solenoid plunger and BLUE spring assembly

and replace it with the solenoid plunger and RED colored spring

assembly. Pull off the actuator cam, and replace it with the fail-safe cam.

Before closing the unit, make sure that the wires are properly seated

on the wire channel (see figure on right). Save the plunger and BLUE

colored spring assembly for future use.

For changing from Fail Safe to Fail Secure, just reverse the

above procedure

4850 THICKNESSES:

Combining the 1/8” spacer and 1/4” spacer the 4850’s open

cavity allows for multiple thicknesses: 1/2”, 5/8“, 3/4” and 7/8”

SYMPTOM: ELECTRIC RELEASE IS NOT ACTUATING:

1. Verify proper voltage is present AT STRIKE. If voltage is present: the strike may have been

affected during the installation, or dirt or debris may be preventing proper operation. Inspect

electric release and clean. NOTE: DO NOT LUBRICATE SOLENOID

2. If voltage IS NOT present:

A) Verify Circuit breaker is on, B) Verify voltage at the transformer/power supply output. C)

Verify that there are no additional, external switches or devices which may be interrupting your

circuit. D) Check for damaged wiring or bad wire splices.

SYMPTOM: STRIKE IS WORKING BUT WILL NOT OPEN:

1. Check for other locks on door

2. Check for proper lock-latch engagement

3. Check for excessive back pressure on door release latch by following these steps:

A) Push the door from the outside to try and relieve the bolt to latch pressure and actuate

the 4800F. B) While the 4850 is unlatched swing the door open. If the door opens, then the bolt

maybe applying pressure to the latch. Adjust the position of the 4850 to relieve the pressure.

POSSIBLE REMEDIES:

1. Re-adjust (or install) a door closer, Remove door silencers, Re-center electric release in jamb,

Remove or trim weather stripping around the door.

Installing this strike on an uneven surface can cause problems with the internal mechanism of

this device. Specifically, it will cause localized mechanical pinching of the moving parts. Locate

where the pinching is occurring and level the frame surface at that location.

(FIG W)

PHONE: (203) 730-1756

FAX: (203) 730-1781

2 Parklawn Dr., Suite F

Bethel, CT 06801

email: [email protected]

website: www.trineonline.com

V. 17.0407

Uneven

Frame Soffit

Ideal Frame

Soffit Flatness

(FIG W)

TRINE 4850 - 1/2” THICK ELECTRIC

THE ONE BOX SOLUTION

FOR RIM PANIC EXIT DEVICES

4850 ELECTRICAL CHARACTERISTICS:

4850

ELECTRIC

STRIKE

4850PoE/4850LCD

INSTALLATION INSTRUCTIONS

Congratulations on the purchase of this quality TRINE
security product. This product has been designed to
install easily, perform reliably, and provide years of trouble
free security.

BEFORE PROCEEDING with your installation, please review the
following list of features. If you have any questions after reading
this document please call TRINE's TECHNICAL SUPPORT

(203) 730-1756

, or visit us online @

trineonline.com

Built-in Electronics: The 4850 automatically allows 12-24DC

power, plus surge and kickback protection. There are no

external ‘pacs’ to use or install.

BHMA Grade 1 Electric Strike

- 1,000,000+ Life Cycles

- 1,500+ lbs Holding Force

Single Locking Mechanism

Pull-in/Hold

Amps (A)