Trine 4100 Electric Strike, Руководство по установке

Страница: 5 / 65

RECOMMENDED PRE-INSTALLATION CHECK:
1. Determine that the door swings without interfering with
jamb or sill; the door must operate properly in order for the
system to provide best results.
2. The door must be equipped with a door closer and the door
closer "latch mode" must hold door in a completely closed
position in order to avoid the lock latch from applying
pressure against the releasing latch portion of the electric
strike.
3. Electrical wire connections must be completed and ready
to be terminated inside the frame.
4. Confirm that the power line in the frame is the correct
voltage and that the switch works properly.
5. Confirm proper clearance exists between the end of the
lock latch and jamb.
6. The faceplate opening used on the electric door strike
must be centered with lock latch centerline when it is
installed on the doorjamb.
7. For best installation results, the door frame must be
reasonably flat and straight.
INSTALLING THE 4200 STRIKE:
NOTE: The 4200 electric strike has two terminal wires to
supply power to two separate solenoids.
1. Prepare door frame as shown on page 2 (based on frame
type).
3
4200 OPTIONS:
4200RS - FAIL SAFE CONFIGURATION
4200LB - LATCH BOLT MONITORING
(coming soon)
4200RSLB - FAIL SAFE/LATCH BOLT MONITORING
(coming soon)
BZ-12 - 12VDC Piezo Buzzer
BZ-24 - 24VDC Piezo Buzzer
Plug the
strike
terminal
in to the
quick
connect
socket.
Quick Connect
Socket
Crimp
Connector
2. Pull the switched power
wires to the door frame.
(Caution: Connect the
power ONLY as the last
step.)
3. Carefully choose the
quick connect socket to
match the required
voltage. The quick connect
sockets are labeled 12VDC
(Blue Wire) or 24VDC
(White Wire).
4. Use the crimp
connectors to terminate
the ends of the quick
connect socket to the
power wires coming out of
the frame.
5. Connect the strikes
bottom terminal to the
quick connect socket.
6. Tuck the wires inside
the door frame.
7. Install the electric strike
into the door frame
8. Connect the power
supply and turn power on.
9. Test your system.
The 4200 Fascia is designed to be replaceable and is available in 5 powder
coat finishes. Replacing the Fascia is easy, follow these steps:
1. Remove top and bottom assembly screws ( see a. ) from the electric strike,
these hold the Fascia ( see b. ) in place.
2. Fascia then slides away from the electric strike -- note two additional holes
( see c. ) that provide stability to the Fascia.
3. New Fascia is aligned to the holes and pushed in until screw holes align.
4. Insert both the bottom and top assembly screws to secure the Fascia into
the electric strike body.
Longer Faceplates have
additional holes. 2 assembly
holes to mount the faceplate to
the electric strike. 2 holes for
mounting the assembled
faceplate/strike to the frame.
Available in 5 powdercoat finishes: Aluminum
(ALUM), Black (BLK), Dark Bronze (DKBZ), Green
(GRN), and White (WHT) which can match the finish
of the faceplate and trim skirts.
1 31/32"
7/8"
2 1/2"
5/32"
STRIKE SIDE
(Included)
FRAME PREPARATION
FACEPLATE DIMENSIONS
REMOVABLE FASCIA
(Match the Color of the Frame)
LONGER FACEPLATE
ASSEMBLY
Metal Frame
TAB
DIMENSIONS
Wood Frame
Use #12-24 x 1/2 inch
Philips Mounting Screws
for tab holes.
Aluminum
Frame
a.
a.
c.
c.
b.
MOUNTING TABS (2)
SUPPLIED
4 7/8"
1 17/64"
4 1/8"
3 3/8"
1 1/16"
8 1/16"
CL
7 15/16"
1 7/16"
3/8" (4)
1 3/4"
7 3/16"
R5/32" (4)
CL
6 7/8"
1 1/4"
3/8" (4)
1 3/4"
6 1/8"
R5/32" (4)
CL
3/8" (2)
4 7/8"
1 1/4"
1 3/4"
4 1/8"
R5/32" (4)
CL
3/8" (2)
4 7/8"
1 1/4"
1 3/4"
4 1/8"
R1/32" (4)
1 3/32"
1 1/4"
4 7/8"
3 3/8"
4 1/8"
4 7/8"
3 3/8"
1 1/4"
1 3/32"
3 11/16"
3/16"
4 1/8"