Trine 4100 Electric Strike Скачать руководство пользователя страница 65

Страница: 65 / 65

USE

A23 12VDC

ALKALINE BATTERY OR IT'S

FOLLOWING EQUIVALENT:

MN21, GP23AE, A23,

VA23GA, MS21

BATTERY SPECIFICATION AND ORIENTATION:

NEGATIVE

SIDE

POSITIVE

SIDE

FCC ID: PFO018-2

018-2 TRANSMITTER

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must

accept any interference received, including interference that may cause undesired operation.

NOTICE REGARDING THE 018-2 TRANSMITTER

TROUBLESHOOTING GUIDE SECTION:

The 017TDC-2 & 3 and the 018-2 operates on radio frequency (RF) signaling and may have some problems being installed in
certain locations. Radio frequency (RF) signals are similar in principle as two people conversing. RF communications however are
more difficult to troubleshoot because RF modulates at frequencies that are not audible to human ears.

Let's say that you and I are comfortably conversing, if a person starts talking loud next to us, then we may start to go closer and
closer to each other until we can once again understand each other.

RF devices will work the same way. The first objective in troubleshooting is to spot the troublemaker, in this case, the offending
device. The offending device can be one or the combination of the following items: light dimmers, fluorescent lights, TV or computer
CRT displays and any piece of equipment using a switching power supply or "clock" oscillator (computers and other digital devices).
Additionally, ham and CB transmitters, remote controls, wireless phones, cellular phones, commercial taxi/police/aircraft radios,
microwave ovens, motion sensors, radar systems, and a myriad of medical and industrial RF devices.

As you can appreciate from the litany of devices above almost any perimeter can have multiple sources of RF noisemakers.
Deciding the final position for mounting the 017TDC will immensely improve your chances of installation success. Before screwing
the 017TDC receiver down, choose an initial location and use a 10 feet electrical cord and walk test the 017TDC's sensitivity to
receive the 018-2's signal. Once you have determine the most ideal spot, that is the place you will install the receiver.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Transmitter does not work
(LED lamp does not light)

Transmitter does not work
(LED lamp turns ON)

Receiver works intermittently

Battery is low

Battery is not properly installed

Transmitter is out of range

Wiring connections may be faulty

Security Code mismatch

Wiring connection may be faulty

RF interference

Security Code mismatch

Faulty power supply

Loose wiring connections or shorted wire

Replace the battery. Use an A23 size 12VDC Alkaline battery.

Reinstall the battery correctly (see battery polarity drawing above)

Move the transmitter closer to the receiver (see above article)

Check your wiring scheme refer to the 017TDC-2 & 3 instruction sheet.

See if your receiver and transmitter security code match (see front page)

Check your wiring scheme refer to the 017TDC-2 & 3 instruction sheet.

Read the article above regarding RF interference

See if your receiver and transmitter security code match (see front page)

Check the power supply for correctness of voltage and capacity

Carefully check all your wiring connections and tighten loose connections

For additional information regarding the 017TDC-2 and 3 Wireless Controllers and to download this document in electronic form (Adobe Acrobat
PDF). Go to our website at http://www.trineonline.com/interior/support/instruction_sheet.html

TRINE ACCESS TECHNOLOGY

1440 Ferris Place

Bronx

New York

10461 Tel. No. (718) 829-2332

Fax No. (718) 829-6405

Website: www.TrineOnline.com

017TDC-3

RELAY CONTROL

SWITCH

RELAY

CHANNEL