manualshive.com logo in svg

Trine 4100 Electric Strike, Руководство по установке

Поделиться
Скачать
Trine 4100 Electric Strike Скачать руководство пользователя страница 46

SIX WIRE SCHEMATIC UTILIZING TWO TRANSFORMERS

This wiring arrangement is used to isolate the strike operation, from the LB and/or the SLIDER sensor and 

power board and the Panel Indicator or Signaling Device.

WHITE - NORMALLY CLOSED (NC)

BLACK -

RED +

BLUE COMMON (COM)

YELLOW - NORMALLY OPEN (NO)

GRAY - NORMALLY CLOSED (NC)

GREEN COMMON (COM)

ORANGE - NORMALLY OPEN (NO)

POWER TO STRIKE

POWER TO STRIKE

120
VAC

12 - 24 VDC

OUTPUT

12 - 24 VDC

OUTPUT

CONTROL SWITCH

OR RELAY

PANEL INDICATOR

OR OTHER 

SIGNALING DEVICE

POWER

SUPPLY 1

120
VAC

POWER

SUPPLY 1

PANEL SIDE

WIRING

FRAME SIDE

WIRING

CONTROL

PANEL

Hook-up to either Normally Open

or Normally Closed Terminal

Hook-up to either Normally Open

or Normally Closed Terminal

EN400, EN800, EN850, EN950, EN960 LBSM WIRING SCHEMATIC

SWITCHED POWER

CONSTANT POWER

FIVE WIRE SCHEMATIC UTILIZING ONE TRANSFORMER

This wiring arrangement uses the least amount of conductors between the Panel and the Frame.

FRAME SIDE

WIRING

120
VAC

12VDC

OUTPUT

CONTROL SWITCH

OR RELAY

PANEL INDICATOR

OR OTHER 

SIGNALING DEVICE

POWER
TRANS-

FORMER

CONTROL

PANEL

PANEL SIDE

WIRING

Hook-up to either Normally Open

or Normally Closed Terminal

Hook-up to either Normally Open

or Normally Closed Terminal

WHITE - NORMALLY CLOSED (NC)

BLACK -

RED +

BLUE COMMON (COM)

YELLOW - NORMALLY OPEN (NO)

GRAY - NORMALLY CLOSED (NC)

GREEN COMMON (COM)

ORANGE - NORMALLY OPEN (NO)

POWER TO STRIKE

POWER TO STRIKE

SWITCHED POWER

CONSTANT

POWER

WIRING SCHEMATICS FOR DIFFERENT APPLICATIONS

1440 Ferris Place  

  Bronx  

  New York  

  10461

Содержание 4100 Electric Strike


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды