manualshive.com logo in svg

Trine 4100 Electric Strike, Руководство по установке

Поделиться
Скачать
Trine 4100 Electric Strike Скачать руководство пользователя страница 43

7) From the top insert latch pin, pushing

assembly pin out.  Latch is now free to open

8) Check the action of the slider to make

sure the slider can move up & down freely

.

10) Check slider action.  Make sure slider is

free to move up & down with no resist

ance.

11) 
Thread wires thru cover as shown.

Replace back cover: Replace 2 screws and

tighten.

9) Replacing coil assembly

.

Note:

Slider must be in position between

bracket

s of coil assembly

.

Note: Position wires thru slot toward front of

the strike.  

The coil must be flush to case

before wscrewing together

.

Inser

t

La

tc

h Pin

Chec

k action

of
Slider

Slider must be

betw

een

br

ac

kets of

Coil Assembl

y

1440 F

er

ris Place

Br

onx,

NY 10461

TEL:

718-829-2332

FAX:

718-829-6405

customer

ser
[email protected]

www

.trineonline.com

Содержание 4100 Electric Strike


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды