Trine 4100 Electric Strike, Руководство по установке

Страница: 3 / 65

TRINE 4200
THE ONE BOX SOLUTION
FOR CYLINDRICAL LOCKS
AND DEADLATCHES
Congratulations on the purchase of this quality TRINE security
product. This product has been designed to install easily,
perform reliably, and provide years of trouble free security.
BEFORE proceeding with your installation, please review the
following list of features. If you have any questions after reading this
document please call TRINE's TECHNICAL SUPPORT (718) 829-2332
EXT. 447 , or visit the TRINE web site at www.trineonline.com
1440 Ferris Place l Bronx l New York l 10461
4200
ELECTRIC
STRIKE
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING THE COMPLETED INSTALLATION:
WIRING DIAGRAMS
DO NOT APPLY A VOLTAGE OF MORE THAN 10% OVER THE
RATED OPERATING VOLTAGE OF THE STRIKE OR THE
SOLENOID WILL BE DAMAGED
SYMPTOM: Electric release is not actuating:
1. Verify proper voltage is present AT THE STRIKE. If voltage is
present, the strike may have been affected during the
installation, or dirt or debris may be preventing proper
operation. Ensure that all moving parts are clean. DO NOT
LUBRICATE THE SOLENOID.
2. If voltage IS NOT present:
· Verify Circuit breaker is on
· Verify voltage at the transformer/power supply output.
· Verify that there are no additional, external switches or
devices which may be interrupting your circuit.
· Check for damaged wiring or bad wire splices.
SYMPTOM: Door will not open but strike is working
· First, check to see if the electric strike works properly
while the door is open.
· Check for proper lock-latch engagement
· Check for pressure from the door on the electric strike
by following these steps:
Push the door from the outside, try and relieve the bolt
to latch pressure and actuate the 4200. While the
4200 is unlatched swing the door open. If the door
opens, then the bolt maybe applying pressure to the
latch. Adjust the position of the 4200 to relieve the
pressure.
Possible remedies include:
1. Re-adjust door closer.
2. Remove door silencers.
3. Remove, or trim, weather stripping around the door.
4. Adjust electric strike position if possible.
5. Correct excessive warping of door.
PHONE: (718) 829-2332
FAX: (718) 829-6405
1440 FERRIS PLACE
BRONX, NY 10461
email: customerservice@trineonline.com
website: www.trineonline.com
4
Current Power
Voltage Draw Consumption Resistance
12DC .240 Amps 2.90 Watts 50 Ohms
24DC .114 Amps 2.74 Watts 210 Ohms
12AC
@ 50-60Hz
.210 Amps 2.50 Watts 50 Ohms
16AC
@ 50-60Hz
.281 Amps 4.48 Watts 50 Ohms
24AC
@ 50-60Hz
.420 Amps 10.08 Watts 50 Ohms
4200 ELECTRICAL CHARACTERISTICS:
Mount the shim with the step aligned
with the top of the latch as so.
This position will ensure that the cylindrical
lock's auxilliary trigger will function properly.
USING THE LATCH SPACER SHIM
The latch spacer shim is used to make an adjustment to
minimize the space between the door's inside face and the door
stop, or reduce door play. For cylindrical locks aligning to the
vertical center of the strike mount the shim as shown below.
OPERATING TEMP RANGE: - 20°C TO +40°C
DO NOT APPLY A VOLTAGE OF MORE THAN 10% OVER THE RATED
OPERATING VOLTAGE OF THE STRIKE OR THE SOLENOID WILL BE DAMAGED
When removing the connector and using the wires direct; Blue Wire is Common,
Red Wire accepts 12DC & 12-16AC, Brown Wire accepts 24DC.
RS IS FAILSAFE ACTION (LOCKS WITH POWER) AND IS DC ONLY
24V DC OR 12V DC
TRANSFORMER
TO 120V AC LINE
PUSH
BUTTON
NORMALLY
CLOSED
+
-
FAIL-SAFE
ELECTRIC STRIKE
USE THE PROPER
CONNECTOR 12VDC OR 24VDC
ASSEMBLY FOR
THE 4200 STRIKE
Cannot use AC in Fail Safe Configuration
24V DC OR 12V DC TRANSFORMER
TO 120V AC LINE
PUSH
BUTTON
NORMALLY OPEN
+
-
USE THE PROPER
CONNECTOR 12VDC OR 24VDC
ASSEMBLY FOR
THE 4200 STRIKE
For AC use the 12 VDC connectors
For 12 - 24 VAC use 50-60 Hz
FAIL-SECURE
ELECTRIC STRIKE
V. 14.0218
CL
3 3/8"
4 7/8"
4 1/8"
1 1/4"
1/4"
1 3/4"
BACKSET
1 1/16"
1 5/8"
1/2”
CAVITY DEPTH
25/32"
32D (630) Satin Stainless
ALUM Aluminum Powder Coat
BLK Black Powder Coat
DKBZ Dark Bronze Powder Coat
GRN Green Powder Coat
WHT White Powder Coat
AVAILABLE FINISHES
1 - (1) 4200 Electric Strike Mechanism
2 - (4) Faceplates as shown
3 - (6) #12-24 x 1/2 inch Philips Mounting Screws
4 - (2) #12-24 Lock Nut
5 - (2) Quick Connect Socket & Wire Assembly 12VDC & 24VDC Version
6 - (2) Sealed Crimp Connectors
7 - (1) Latch Spacer Shims & (2) Mounting Screws
8 - (1) Frame Trim Skirt & (2) Screws
9 - (2) Mounting Tabs
WHAT'S IN THE BOX:
Auxilliary Trigger
PREMIUM TRIM SKIRT FOR THE 4200
USING THE TRIM SKIRT
The skirt can be used to clean up the
cut line of the frame face during
installation. The Trim Skirt comes
with 2 longer screws (included) for
fastening to the top and bottom of
the 4200.
Available in 5 powdercoat finishes:
Aluminum (ALUM), Black (BLK), Dark
Bronze (DKBZ), Green (GRN), and
White (WHT) which can match the
finish of the faceplate and Fascia’s.
RS IS FAILSAFE ACTION (LOCKS WITH POWER) AND IS DC ONLY