T
O
CHECK
TRANSFORMER
OPERA
TION
, check to
see that the fuse or circuit breaker is on.
Then touch
the two low volt
age transformer terminal screws with
a low volt
age meter which should read no less than
13 volt
s. If you do not have a meter
, touch the two
screws with a screwdriver
.
A
small sp
ark indicates
the transformer is operating. If no sp
ark is evident,
replace the transformer with another transformer
.
T
O
CHECK
CHIME
OPERA
TION
disconnect one wire
from the chime. Have someone hold down the push
button and touch the disconnected wire to the center
screw terminal of the chime.
A
small sp
ark will indi-
cate the wiring and transformer are working
Most doorbells, buzzers or small chimes in use today
operate on a 10 volt transformer which should be
replaced with a 16 volt-10 watt type for superior
sound volume
Product specification subject to change without notice
DOOR CHIME
INST
ALLA
TION INSTR
UCTIONS
NEW INST
ALLA
TION
PLA
CEMENT OF THE COMPONENTS.
Spend some time planning the loca
tion of
all the par
ts in y
our door c
hime system.
DOOR
CHIMES are best mounted in a central loca-
tion so they can be heard throughout the home. If it
is to be a multiple chime inst
allation, you may also
want to plan for central locations, e.g., entryways,
hallways second floor landings, etc.
For best appearance, locate your chime 78” above
the floor line.
Door chimes are decorative, as well as functional.
Place them at eye level as you would any picture or
artwork.
HO
W
T
O
T
O
CHECK PUSH BUTT
ON OPERA
TION
remove
button from wall. Disconnect both wires from but-
ton.
Touch exposed wires together
. If your chime
sounds, the push button is defective. Replace with
a new push button.
PROPER
CHIME
MOUNTING
Door chimes can be mounted in either a horizont
al
or vertical position.
FOR REPLA
CEMENT INST
ALLA
TION
(not requiring a transformer change).
For replacement inst
allatin requiring a new transformer
, follow additional
step
s 2 through 4 of New Inst
allations).
1. Remove cover from existing chime and disconnect wires from terminal
screws. Label all wires (Front,
T
ransformer
, Ream) as you remove them.
2. Remove existing chime base from wall.
3. Pull wires through holes in new chime base.
4. Use provided screws to mount base to wall.
5.
Connect wires to terminal screws marked
Front,
T
ransformer and
Rear on the chime base.
6. Place chime cover securely over the base.
NOTE: FOR LOUDER SOUNDING CHIME PERFORMANCE,
A
20V
A
TRANSFORMER IS RECOMMENDED (MODEL
598)
FRONT
AND REAR DOOR INST
ALLA
TION OF DIAGRAM OF
MUL
TIPLES CHIMES
FRONT
AND REAR DOOR INST
ALLA
TION DIAGRAM
FRONT
REAR
TRANSFORMER
120V
AC WIRING
FRONT
REAR
TRANSFORMER
120V
AC WIRING
NEW CHIME INST
ALLA
TIONS REQUIRE
TRANSFORMERS
WARNING:
TURN OFF HOUSE
PO
WER
BEFORE ST
ARTING
YOUR INST
ALLA-
TION OF
YOUR TRANSFORMER. F
AIL-
URE T
O
DO SO MA
Y
RESUL
T IN DAN-
GER FROM ELECTRICAL
SHOCK.
TRANFORMERS should be mounted on or near a
junction box.
They can also be mounted to the
electrical service p
anels. Junction boxes utility
rooms, crawl sp
aces, or basement
s are preferred.
A
void att
ack locations whenever possible.
Chimes operate best with a 16 volt, 10 watt,
AC
transfomer (no.522). For multiple chime operation
we recommend using a 16 volt, 20 watt,
AC
trans-
fomers (Nos 598). Failure to use a t
ansformer with
adequate cap
acity will result in loss of sound or
may result in the system being inoperative.
PUSH
BUTT
ONS
are usually mounted in the same area of
front
al reach as the door controls, at height of 36” to 44” above
the doorsill.
NEW
INST
ALLA
TIONS
1. Locate chime at eye level so it can be seen as well as heard.
2.
W
ARNING
FOR TRANSFORMER OPERA
TION ONL
Y, TRUN OFF HOUSE POWER BEFORE
ST
ARTING INST
ALLA
TION. F
AILURE T
O
DO SO MA
Y
RESUL
T IN DANGER
FROM ELECTRICAL
SHOCK.
3. Mount a (no. 522) transformer to a conventinet junction box (attic location ot rec-
ommended) or circuit breaker box.
4. Connect transformer wires to house power
, one black transformer wire to one
black house lead, the other black transformer wire to teh white house lead. Using
electrical t
ape and/or wire nut
s, insulate each connection (sep
arately).
Att
ach green
transformer wire to junction box, to ground wire or clamp to conduit.
5. Follow wiring diagram and run st
andard chime/bell wires from transformer and
push button(s) terminals to chime. Label all wires - Front, Rear
,
T
ransformer
6.
Pull wires through holes in chime base.
7. Use provided screws to mount base to wall
8. Connect transformer and push button wires to terminal screws marked Front,
T
ransformer and Rear on the chime base.
9. Place chime cover securely over the base.
10. Restore power
. Press push button(s) to test chime.
UP
Содержание 4100 Electric Strike
Страница 25: ......
