manualshive.com logo in svg

TriContinent 8441 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
TriContinent 8441 series Скачать руководство пользователя страница 6

1 INSTALLATION

1.1

UNPACKING

REFER TO THE INSTRUCTIONS AND PICTURES ON THE BOX.

1. Place the shipping carton on the floor for easy access and removal of equipment.
2. Remove the reservoir kit using the pull handle.
3. Remove the foam cushions from the sides.

IMPORTANT: DO NOT LIFT THE WASHER BY HOLDING THE SYRINGE ON THE BACK 
OF THE INSTRUMENT.

4. Place hands UNDER the front and rear of the instrument and pull up to remove instrument 

from the carton.          

5. Remove the accessories and AC line cords from the box.
6. Refer to the shipping checklist below to verify that all items on the list have been received. 
7. Inspect all components for shipping damage. In case of damage, contact the shipper who 

delivered your equipment.

8. Save all packaging material in case it becomes necessary to return the instrument.

Shipping Checklist

MultiWash III instrument
Reservoir kit (Wash, Rinse and Waste)
AC Power Supply Cables (USA domestic, 120V; European, 220V)
Bag containing spare fuses, instructions and  soaking microstrip wells
This manual:  MultiWash III Operation and Maintenance,
Quick Start Guide

1.2

ENVIRONMENTAL REQUIREMENTS

Locate the MultiWash III so that it is shielded from excess exposure to dust, vibration, strong 
magnetic fields, direct sunlight, drafts, excessive moisture, or large temperature fluctuations.  A 
surge protector or line conditioner should be used with the instrument if the voltage source is 
not stable.  Sudden voltage spikes can cause damage to the electronics inside the instrument.
Operating temperature:

10° to 40° C

Storage temperature:

1° to 40° C

Operating altitude:

Up to 2000 Meters

Maximum relative humidity:

80%, non-condensing up to 31° C decreasing linearly to 50% 
relative humidity at 40° C

Pollution:

Degree II

Equipment installation:

Minimum of 20 cm required between back panel assembly 

and walls or objects to service fuses and AC line cords.

Multiwash III

1

Содержание 8441 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды