manualshive.com logo in svg

TriContinent 8441 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
TriContinent 8441 series Скачать руководство пользователя страница 22

3.3

PROGRAMMING A WASH CYCLE

3.3.1 PROGRAM NUMBER

The instrument will save up to 50 user-
entered wash sequences in "programs", 

numbered 1 through 50.  Press 

 until the flashing arrow appears next to PROGRAM 

NUMBER.  The display will show the current program number.  Press 

 or 

 to 

change to another program.  Any entries for Dispense Volume, Dispense Speed, Soak 
Seconds, Wash Cycles, Strip/Plate Wash Mode, and plate type will be saved in this program 
number.

3.3.2 MANIFOLD/SELECT

Press 

 and the currently selected 

manifold for the program will be displayed.  If 
the manifold selection is changed, then all of 
the following programmed values should be 

reviewed before running the program.  Press the 

 or 

 to move between "8", "12" or 

"2-8" port manifold.  The display will show which manifold has been selected.  The maximum 
value of rows will change to 8 rows when the 12-port manifold is displayed.

WARNING: THE 2-8 PORT MANIFOLD OPTION IS NO LONGER AVAILABLE. SELECTING 
THIS OPTION WILL CAUSE THE WASHER TO SKIP ROWS FOR THE STANDARD 8-PORT 
MANIFOLD.

3.3.3 DISPENSE VOLUME

Press 

 until the flashing arrow appears 

next to DISPENSE VOLUME and the volume is 

displayed.  Adjust the dispense volume by pressing 

 or 

 in 10 µl increments.  The 

display shows the per-well volume, regardless of 8, 12 or 2-8-port manifold selection.  
Maximum volume is dependent on the manifold selected, see Section 6.1 for additional 
information.

3.3.3.1

TO ASPIRATE ONLY

A) Set the DISPENSE VOLUME to zero.

B) The number of WASH CYCLES must be 

adjusted to 

greater 

than zero.

The washer will then aspirate the fluid and 
will not dispense any liquid into the wells.

Select

Review

Manifold

Select

Select

Review

Multiwash III

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

17

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

u L

Содержание 8441 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды