manualshive.com logo in svg

TriContinent 8441 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
TriContinent 8441 series Скачать руководство пользователя страница 20

3.1.4 RINSE

The plate washer should be rinsed daily after use.   The Rinse uses distilled water to purge the 
syringe, tubing and manifold of wash solutions. See Section 6.1 for Rinse cycle volume usage.

Press 

 to start.  Press 

 to cancel.  During rinsing, the display will show 

"rin"

.

3.1.5 ROWS

The ROWS key allows the operator to select the desired number of rows on the microplate to 
be processed.  Twelve rows is the maximum number when using an 8-port manifold.  Eight 
rows is the maximum number when using a 12-port manifold.  Twelve rows, changing only in 
increments of 2 rows, is the maximum number when using a 2-8-port manifold.

Press 

 to initiate setting.  Then use the 

 or 

 key to select the number of rows.

Press 

 to return to menu.  When 

 is pressed, the number of rows selected will be  

displayed.

3.1.6 AUTOMATIC STANDBY-ROW REFILL
If the power to the instrument is left on

, the liquid in the standby row will automatically be 

aspirated and refilled every 8 hours to prevent the manifold needles from drying out. 
To maintain the Multiwash III's reliability, the instrument performs a maintenance rinse of the 
standby row after eight hours of non-use.  

It is important to leave the power on to the 

instrument at all times for this maintenance rinse function to occur.  Leaving the power 
on is critical if the Wash solution is not routinely purged from the instrument after use.

  

This rinse operation is designed to keep Wash solution from drying and leaving clogging salt 
deposits between uses.  

It is the user's responsibility to connect the Rinse reservoir filled 

with distilled water to the instrument.

  The maintenance rinse will continue after every eight 

hours of non-use.

If the Multiwash III is to be turned off, it is important to purge the Wash solution 
completely out of the system to prevent damage. 

 This can be accomplished by performing 

the Rinse operation twice with distilled water.

3.1.7 WASTE RESERVOIR FULL SENSOR

When the liquid in the Waste reservoir covers the end of the sensor probe, the instrument will 

beep and display 

"FUL"

 when 

 is pressed to begin a plate wash.  Empty the Waste 

reservoir.  The waste sensor must be plugged into the jack on the rear panel before a plate 
wash can begin.

NOTE:  It is also recommended that the Wash reservoir be refilled at this time.

R inse

Start

Stop

R ows

R ows

R ows

Start

Stop

Multiwash III

15

Содержание 8441 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды