manualshive.com logo in svg

TriContinent 8441 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
TriContinent 8441 series Скачать руководство пользователя страница 23

3.3.4 DISPENSE SPEED

Press 

 until the flashing arrow 

appears next to DISPENSE SPEED.  Press 

the

 

 and 

 keys to adjust the initial speed up and down.

The DISPENSE SPEED is the rate at which the liquid will be dispensed from an individual 
manifold needle.  The DISPENSE SPEED requirement will vary depending on the application.  
For an 8-port manifold, the range is 150 µl/sec to 500 µl/sec and for the 12-port it is 150 µl/sec 
to 400 µl/sec.

3.3.5 SOAK SECONDS

Press 

 until the flashing arrow appears 

next to SOAK SECONDS and the soak time 
is displayed.  Set the soak time by pressing 

 or 

.  Maximum soak time is 999 seconds.

3.3.6 WASH CYCLES

Press 

 until the flashing arrow appears 

next to WASH CYCLES and the number of 

cycles is displayed.  Set the number of wash cycles by pressing 

 or 

.  Maximum 

number of cycles is 10.

3.3.6.1

TO DISPENSE ONLY

Set WASH CYCLES to 0, then the total volume will be dispensed into each well without 
aspiration.

3.3.7 STRIP/PLATE MODE WASH

Press 

 until the flashing arrow appears 

next to STRIP/PLATE MODE WASH.

Press 

 or 

 to toggle between “SP” = STRIP or “PL” = PLATE wash modes.  When 

“PL”, PLATE WASH MODE is selected, the arrow will remain displayed as a visual reminder 
that Plate Wash mode has been selected for this program.

Select

Review

Select

Review

Select

Review

Select

Review

Multiwash III

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

18

PROGRAM NUMBER

 DISPENSE VOLUME

DISPENSE SPEED

SOAK SECONDS

WASH CYCLES

STRIP/PLATE WASH MODE
        PLATE SELECTION
2-8 PORT MANIFOLD
12 PORT MANIFOLD
8 PORT MANIFOLD

u L

Содержание 8441 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды