manualshive.com logo in svg

TriContinent 8441 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
TriContinent 8441 series Скачать руководство пользователя страница 4

Multiwash III

CONTENTS (CONTINUED)

4

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4.1

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4.2

MAINTENANCE SCHEDULE AND SERVICE RECORD . . . . . . . . . . . . . . . . . . . . 22

4.3

INLET LINE FILTERS-WASH AND RINSE RESERVOIRS. . . . . . . . . . . . . . . . . . . 22

4.4

ASPIRATE EXHAUST FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4.5

DISPENSE PUMP AND SYRINGE ASSEMBLY ON BACK PANEL . . . . . . . . . . . . 25

4.6

CLEANING MANIFOLD NEEDLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.7

REPLACING STANDARD MANIFOLD DISPENSE NEEDLES . . . . . . . . . . . . . . . 27

4.8

INSTALLING MANIFOLD TUBING (CONTINUED) . . . . . . . . . . . . . . . . . . . . . . . . 28

4.9

FUSE MODULE REMOVAL AND FUSE INSTALLATION INSTRUCTIONS. . . . . . 29

4.10

DECONTAMINATION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.1

RE-INITIALIZING THE STORED PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.2

TROUBLESHOOTING TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.3

ERROR CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.4

USER TROUBLE SHOOTING NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

6

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

6.1

PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

6.2

MECHANICAL/ELECTRICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

APPENDIX 1

ACCESSORIES AND REPLACEMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

APPENDIX 2

ORDERING INFORMATION/CUSTOMER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

WORKMANSHIP AND MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
EXCLUSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

APPENDIX 3

QUICK START GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

v

Содержание 8441 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды