manualshive.com logo in svg

TriContinent 8441 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
TriContinent 8441 series Скачать руководство пользователя страница 18

2.6

DISPLAY

The display on the front of the Multiwash III indicates the current setting of selected 
parameters and, during washes, indicates status.  Arrows at the left edges of the display 
indicate the currently selected parameter.  For example, when the arrow next to the 
"DISPENSE VOLUME" label on the front panel is visible, the current dispense volume setting 

is displayed and can be changed, using the 

 and 

 buttons.

Arrows at the right edge of the display indicate which wash mode setting (see Section 3.3.7) is 
selected, whether the instrument is set for flat bottom or U-/V-bottom microplates (see Section 
3.3.8) and whether the instrument is set for an 8-port manifold or 12-port manifold.

During Prime, 

"Pri" 

is displayed to indicate the instrument is completing the prime routine. 

During soak times, the remaining soak time is displayed.

During Rinse, 

"rin"

 is displayed to indicate the instrument is completing the rinse routine.

To indicate completion of a wash.  The display flashes 

"---"

 for approximately 10 seconds and 

then the instrument beeps twice. 

The display will show "FUL" when the Start/Stop key is pushed and the Waste reservoir is full. 
Empty the Waste reservoir and the instrument will then begin a wash cycle when the Start/Stop 
key is pushed.

The display will show error codes when there is a problem with the instrument and stop 
working.  Your distributor should be contacted for additional assistance (see Appendix 2) and 
the troubleshooting guide in Section 5.2 and the error code table in Section 5.3 gives additional 
assistance.

2.7  AUTORINSE VALVE 

During the Wash and Prime modes, the AutoRinse valve is positioned to use the Wash 
solution.  There is no movement of the AutoRinse valve when the instrument is switched 
between the Wash and Prime modes.  The AutoRinse valve operates only after the Rinse 
button has been pushed or after 8 hours of non-use.  The instrument is designed for the 
AutoRinse valve to automatically switch to the Rinse Reservoir position and the Multiwash III to 
flush the lines of Wash solution after 8 hours of non-use.  The soaking microstrip is then refilled 
from the Rinse Reservoir.  The Multiwash III instrument will then continue to aspirate and refill 
the soaking microstrip every 8 hours from the Rinse Reservoir.  When the Start/Stop button is 
pushed to use the Multiwash III again, the AutoRinse valve will then rotate back into the Wash 
solution position.  The instrument will first go through the Prime cycle to flush the lines of the 
Rinse solution, then begin the Wash sequence.

Multiwash III

13

Содержание 8441 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды