manualshive.com logo in svg

TriContinent 8441 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
TriContinent 8441 series Скачать руководство пользователя страница 36

5

TROUBLESHOOTING

5.1

RE-INITIALIZING THE STORED PROGRAMS

To re-initialize the Multiwash III's program settings, hold the Down Arrow key on the keypad as 
you turn the power switch on. This will return all user defined programs back to the factory 
settings!

5.2

TROUBLESHOOTING TABLE

The following checklist may help resolve problems in the operation of this equipment. Any 
problems that cannot be resolved by following the procedures below should be referred to 
qualified service personnel.

Multiwash III

SYMPTOM

PROBABLE CAUSE

REMEDY

1.

Instrument is “dead”. Display is 
blank, the beeper does not 
sound when keys are pressed 
and motors do not operate.

AC power not getting to the 
instrument. Check Power Supply 
cable.
Blown fuse.

Connect to Power Supply Cable.

Instrument setup for the wrong 
voltage.

Replace fuse with proper type. See 
Section 4.9.

Change voltage selector to the 
correct position. See Section 1.3.

2.

Instrument doesn’t respond to 
key presses.

Invalid data in instrument’s stored 
programs. Caused by voltage 
spikes or fluctuations.

Hold “Down Arrow” key while 
turning on power to restore 
operation. A line conditioner or 
surge protector needs to be used. 
See Section 1.2.

3.

Manifold hits plate when 
aspirating rows.

The manifold is not calibrated to the 
proper position within the wells.

Calibrate horizontal manifold 
position. See Section 1.5.2.

4.

Instrument aspirates wells only 
partially, or not at all.

The manifold aspirate needles are 
partially or completely clogged.

Clean needles with supplied tool. 
See Section 4.6.

Tubing is kinked or obstructed or is 
not connected properly.

Check connections, replace worn 
out tubing.

The waste reservoir cap is loose, or 
fittings on cap are loose.

Tighten Waste reservoir cap, on 
bottle and all fittings.

Manifold aspiration needles are not 
optimized for final aspiration.

Adjust Horizontal manifold position 
Section 1.5.2. Adjust vertical 
manifold position Section 1.5.3. 
Verify correct plate selection 
Section 3.3.8.

31

Содержание 8441 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды