manualshive.com logo in svg

TriContinent 8441 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
TriContinent 8441 series Скачать руководство пользователя страница 42

Multiwash III

37

APPENDIX 1  ACCESSORIES AND REPLACEMENTS

To view or download Accessories and/or Replacement items for the MultiWash III, please visit 
our website 

APPENDIX 2

ORDERING INFORMATION/CUSTOMER SERVICE

Assistance with the operation or repair of the MultiWash III is available by contacting:
TriContinent, 12555 Loma Rica Drive, Grass Valley, CA  95945.
From within the United States, telephone (800) WE-PIPET (800-937-4738).
From outside of the United States, telephone (530) 273-8888.
FAX (530) 273-2586

WARRANTY

WORKMANSHIP AND MATERIALS

The Multiwash III is warranted against defects in materials and workmanship for a period of 
two years from the date it is shipped from the manufacturer.  If notified of such defects during 
the warranty period, manufacturer will, at its option, either repair or replace products which 
prove to be defective. Please refer to the TriContinent website 

 for 

detailed warranty and return information.

SERVICING

DO NOT ship the instrument back for repair until you are advised to do so.
DO NOT attempt to repair the instrument, removing the case will nullify the warranty.  In the 
event that the product is inoperable please call or fax your distributor and they will provide full 
failure details.  When making your call, please ensure that you have the serial number of the 
instrument.
In the event that you are requested to return the instrument or any parts thereof IT IS YOUR 
LEGAL REQUIREMENT to ensure that the instrument is fully DECONTAMINATED (see 
section 4.10) and that a certificate to verify decontamination is present in the returned box.  
Failure to do this may result in the refusal to repair the instrument.  Your distributor will issue a 
Return Material Authorization (RMA) number.  This number is to be marked on the outside of 
the shipping box.

EXCLUSIONS

The above warranty shall not apply to defects resulting from improper or inadequate 
maintenance by the customer, unauthorized modification or service, misuse, operation outside 
of the environmental specifications for the product, or instruments returned with inadequate 
packaging.  It is the responsibility of the purchaser to determine the suitability of an application 
and material compatibility of the products.  There is also no warranty expressed or implied for 
valves, syringe plungers or seals.  For equipment damaged in shipping, contact the shipper.

www.tricontinent.com

www.tricontinent.com

Содержание 8441 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды