Trackmaster FVX325, Руководство по обслуживанию на месте

Страница: 71 / 205

TRACKMASTER
6-8
FVX, TMX Series Service Manual August, 2006
FVX325C, TMX425C Series Elevation Calibration Procedure
Tools Required
Tape
Measure
1/4” Allen Wrench
1. Remove front rail end bolt and end cap on TMX425 Series.
2. With power “ON”, press and hold the Speed + and Elevation - keys. After a few
seconds “P 1" should appear in the center window. (Sometimes you must release and
hold these keys again in order to get into this function.)
(Use the Elevation Arrow Keys to make Changes in P categories.)
3. “P 1" in Center window - “bri” in Speed window. ( bri = Mph, Si = Kph) Use UP or
DOWN Incline key to toggle between, then press the Select key.
4. “P 2" in Center window - “0.5" in the Speed window. ( Minimum speed)
Use UP or DOWN Speed key to adjust settings, and then press the Select key.
5. “P 3" in Center window - “12.0" in the Speed window. ( Maximum speed)
Use UP or DOWN Speed key to adjust settings, and then press the Select key.
6. “P 4" in Center Window - “25" in the Incline window. (Incline Cal.) Use UP or
DOWN Elevation key to adjust setting, and then press the Select key.
7. “P 5" in the Center window - “25" in the Incline window. (Incline Max.) Use the UP
or Down Elevation key to adjust setting, and then press the Select key.
8. “P 6" in the Center window - “4" in the Speed window. ( Do not adjust)
Use UP or DOWN Speed key to return to “4", then press the Select key.
9. “P7" in the Incline window - “3175" in the Center window. (Do not Adjust) Use UP
or DOWN Speed key to return to “3175", then press the Select key.
10. “P8" in the Center window, “Hr” in Incline, and “Ser” in the Speed window (Hr =
Heart rate, Ser = Serial input, PU = Pulse input) Use the UP or DOWN Incline key to
toggle between 9.
11. “P9" ECG Equipment Type Operation (nor for all but Medgraphics = GrA)
12. “P10" RS232 Port Select On (Turn to Off when port is not being used)
13. “P11" Time Amount Select (Default = 15, Can not set lower than 15 minutes
14. “P12" Timer Mode On or Off (Default = Off) (When On, P11 set time is up will go
to Cool Down mode.)
15. “P12” Cool down time (Default 60 sec)
16. Hours Distance
ƒ Press the Select key and “HrS” will appear in the Incline window (HrS =
Total hours displayed in center window and minutes in Speed window.)
ƒ Press the Select key and “dIS” will appear in the Center window. (dIS =Total
Distance - Miles in the Incline window, Tenths in the Speed window)
17. Cal S - Press the Select key and “CALS” appears in the Center window
ƒ Pressing the Speed + and the Incline - keys will change Center display to
“CAL” and then pressing the start key will run unit through speed calibration.
ƒ Start speed to 1 Mph or 2 Kph
ƒ Measure belt with MPH gage, verify within spec. +/- 2%.
ƒ Repeat process for 2,3, 5, 7, & 12 MPH or 4, 6, 8, 12 and 19 KPH.
ƒ If not within tolerance, recheck roller ratio, inverter settings, & recalibrate belt.
ƒ Repeat steps 16.2 thru 16.4 until within tolerance.
ƒ Stop Belt