Toshiba MML-AP0074NH-E, Руководство по обслуживанию

Страница: 92 / 132

EN
7
HANDLING THE REMOTE CONTROLLER
CAUTION
• The air conditioner will not operate if curtains,
doors or other materials block the signals from the
remote controller to the indoor unit.
• Prevent any liquid from falling into the remote
controller.
Do not expose the remote controller to direct
sunlight or heat.
• If the infrared signal receiver on the indoor unit is
exposed to direct sunlight, the air conditioner may
not function properly.
Use curtains to prevent the sunlight from reaching
the receiver.
• If the room using the air conditioner has fl uorescent
lighting with electronic starters, signals may not be
properly received. If you are planning to use such
fl uorescent lamps, consult your local dealer.
• If other electrical appliances react to the remote
controller move these appliances or consult your
local dealer.
Q
Location of the remote controller
• Keep the remote controller where its signals can reach
the receiver of the indoor unit (a distance of 7 m is
allowed).
• When you select the timer operation, the remote
controller automatically transmits a signal to the indoor
unit at the specifi ed time.
If you keep the remote controller in a position that
hinders proper signal transmission, a time lag of up to
15 minutes may occur.
Q Remote controller holder
Installing the remote controller holder
• Before you actually install the remote controller holder
on a wall or pillar, check whether the remote controller
signals can be received by the indoor unit.
Mounting and removing the remote controller
• To mount the remote controller hold it parallel to the
remote controller holder and push it in fully.
To remove the remote controller slide the remote
controller upwards and out from the holder.
8
HOW TO USE REMOTE CONTROLLER
Q
Cooling/heating/fan only operation
Start
1
START/STOP button ( )
Press this button to start the air conditioner.
2
Mode select button (MODE)
Select Cool , Heat , or Fan only .
3
Temperature button (
TEMP
)
Set the desired temperature.
When the air conditioner is in FAN ONLY operation,
the temperature display is not indicated.
NOTE
• When the indoor unit is operated together with a
cooling only outdoor model outdoor unit, appears
on the remote controller but the heating operation is
disabled.
• In the cooling operation, airfl ow is blown out only
from the upper air outlet grille under some operating
conditions.
PRESET
MODE
TEMP
FAN
3
4
1
2
4
Fan speed button (FAN)
Select one of LOW , LOW
+
,
MED , MED + ,
HIGH .
• The OPERATION lamp (green) on the display
panel of the indoor unit goes on. And operation starts
after approximately 3 minutes. (If you select FAN
ONLY mode, the unit will start immediately.)
• The : Fan only mode does not control temperature.
• Fan
speed is the same as HIGH .
Therefore, perform only steps 1, 2 and 4 to select this
mode.
Stop
START/STOP button (
)
Press this button again to stop the air conditioner.
1112750101_(01_EN).indd 13
Q
Dry operation
Start
1
START/STOP button ( )
Press this button to start the air conditioner.
2
Mode select button (MODE)
Select DRY .
3
Temperature button (
TEMP
)
Set the desired temperature.
• The fan speed display indicates
• The OPERATION lamp (green) on the display
panel of the indoor unit lights, and operation starts
after approximately 3 minutes.
Stop
START/STOP button (
)
Press this button again to stop the air conditioner
PRESET
MODE
TEMP
FAN
3
1
2
Q
Automatic operation (auto changeover)
This function is available only for use in combination with
a heat recovery model outdoor unit. If this function is
used with another model of outdoor unit, “A” (Auto)
appears on the remote controller but the automatic
operation is disabled.
Start
1
START/STOP button ( )
Press this button to start the air conditioner.
2
Mode select button (MODE)
Select A.
3
Temperature button (
TEMP
)
Set the desired temperature.
4
Fan speed button (FAN)
Select one of LOW , LOW + ,
MED , MED
+
, HIGH .
• The OPERATION lamp (green) on the display
panel of the indoor unit lights.
The operating mode is selected in accordance with
the room temperature and operation starts after
approximately 3 minutes.
• If the “A” mode is uncomfortable, you can select the
desired conditions manually.
Stop
START/STOP button (
)
Press this button again to stop the air conditioner.
PRESET
MODE
TEMP
FAN
3
4
1
2
NOTE
In the dry operation, airfl ow is blown out only from the
upper air outlet grille.
1112750101_(01_EN).indd 14 12/15/10 11:25 AM
91