Toshiba e-studio 211c Скачать руководство пользователя страница 192

Страница: 192 / 225

9-23

If test stapling fails to be performed and the following mes-
sage remains displayed, repeat the above procedure from steps
1 to 12.

Set staple cartridge

Confirm that the finisher is attached to the copier,

and that the paper size is set to any size other

than ST-R.

- Test stapling cannot be performed when only ST-R paper is

available.

Close the front cover of the finisher. Test stapling

is then automatically performed on a blank sheet.

- This operation is carried out to avoid empty stapling.

Saddle Stitch Unit (MJ-1020 only)

Open the lower cover of the finisher.

Reinstall the stapler unit in its previous position and

turn the blue lever 90

to the right to latch the sta-

pler unit.

Содержание e-studio 211c


































































































































































































































Результаты поиска

Содержание e-studio 211c

Отзывы:

Похожие инструкции для e-studio 211c

Бренды по названию

Популярные бренды

Toshiba e-studio 211c, Руководство оператора

Результаты поиска

Содержание e-studio 211c

Отзывы:

Похожие инструкции для e-studio 211c

Бренды по названию

Популярные бренды