Toshiba e-studio 211c Скачать руководство пользователя страница 190

Страница: 190 / 225

9-21

6. ADDING STAPLES (OPTIONAL)

When the staple cartridge runs out of staples, the following message appears:

Set staple cartridge

Add staples to the cartridge according to the procedure below.

Finisher

Open the front cover of the finisher.

Close the front cover of the finisher, and about 10

seconds later, open it again.

- The stapler unit has moved to its specified position.

- Do not move the stapler unit without performing the above

procedure, or it will be broken.

Turn the blue lever 90 degrees to the left and pull out

the stapler unit.

Pull up the stapler unit.

Pull out the staple cartridge.

Содержание e-studio 211c


































































































































































































































Результаты поиска

Содержание e-studio 211c

Отзывы:

Похожие инструкции для e-studio 211c

Бренды по названию

Популярные бренды

Toshiba e-studio 211c, Руководство оператора

Результаты поиска

Содержание e-studio 211c

Отзывы:

Похожие инструкции для e-studio 211c

Бренды по названию

Популярные бренды