Toshiba e-studio 211c Скачать руководство пользователя страница 124

Страница: 124 / 225

6-31

If the chart is not properly placed, the following message ap-
pears:

Set chart correctly

Go back to step 6 and place the chart again.

Press the

START key.

- When the message “READY” appears, the entire operation

is completed.

When the display on the right appears, place the chart

face down on the glass and with its bottom toward

you and its top left aligned against the original scale

on the left side, in order that the black line be placed

at the left side.

The chart is printed out.

Press the CALIBRATION key.

If you want to return the image quality level to the default
setting, press the DEFAULT key.

Содержание e-studio 211c


































































































































































































































Результаты поиска

Содержание e-studio 211c

Отзывы:

Похожие инструкции для e-studio 211c

Бренды по названию

Популярные бренды

Toshiba e-studio 211c, Руководство оператора

Результаты поиска

Содержание e-studio 211c

Отзывы:

Похожие инструкции для e-studio 211c

Бренды по названию

Популярные бренды