Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 91 / 142

MOWER DECK

6-10

Toro TimeCutter SS/MX/ZS Service Manual

Mower Deck Installation

1� Park the unit on a level surface and disengage the

PTO switch�

2� Move the motion control levers outward to the park

position, stop engine, remove key, and wait for all

moving parts to stop before leaving the operating

position�

3� Slide the deck under the unit�

4� Set the height-of-cut to the lowest position�

5� Lift the rear of the deck and guide the hanger

brackets onto the rear lift rod (Fig� 103)�

Fig. 102

fig. 62 G017643

6� Slide the deck rearward to remove the deck belt

from the engine pulley�

7� Slide the deck out from underneath the unit�

Note: Retain all parts for future installation.

A� Idler pulley

E� Engine pulley

B� Deck belt

F� Spring tool

C� Spindle pulley

G� Deck handles

D� Spring

Fig. 103

fig. 61 G005077

A� Deck

C� Rear lift rod

B� Hanger brackets

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды