Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 56 / 142

CHASSIS

3-33

Toro TimeCutter SW/SWX Service Manual

STEERING SYSTEM - ALIGNMENT - ZERO TURN TRACTOR

Alignment

Note: For proper alignment, you will need

three 1/4 in. dowel pins and a steering arm

spacer. This tool kit is available from Toro.

“Order part number 132-0852

Note: The fourth dowel pin is used for a

different procedure.

1. Ensure the wheel gears are in the forward

position so that the tie rod end hole in the gears

are straight forward.

2. Align the mark on the sector gear with a tooth on

the lower steering shaft as shown. The mark on

the gear must be right in the middle.

3. Remove the front shroud as outlined in “Front

Shroud” Service Information Sheet. On the

top of the mower and in front of the steering

column, place the steering arm spacer in the

hole directly in front of the steering colunmn.

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды