Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 57 / 142

CHASSIS

3-34

Toro TimeCutter SW/SWX Service Manual

STEERING SYSTEM - ALIGNMENT - ZERO TURN TRACTOR

The spacer should surround the nut on the tie rod

and verifying the steering column is straight.

4. If the right side wheel (when sitting on machine)

is not straight, adjust the tie rod ends on the

short tie rod (A) until the wheel is positioned in

a straight forward position.

5. If the left side wheel (when sitting on the

machine) isn’t straight, adjust the tie rod on the

long tie rod (B) until the wheel is positioned in a

straight forward position.

6. Insert on of the 1/4 in. dowel pins through the

holes in the speed control assembly and

through the hole in the frame.

If the pin does NOT fit, you will need to install

a pin through the traction pedal and adjust the

tie rod end on the pivot lever assembly. See

steps 3 and 5 in the “Speed Control Assembly”

Service Instruction Sheets.

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды