Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 46 / 142

CHASSIS

3-23

Toro TimeCutter SW/SWX Service Manual

SPEED CONTROL ASSEMBLY - ZERO TURN TRACTOR

Cable Adjustment

1. When the cables are properly adjusted, both of

the cable arms will contact the cabel lever at the

same time when the wheels are straight and the

traction pedal is in neutral

The cable arms should contact the rollers

and stop on the bracket before the cables are

installed and adjusted.

2. If adjustment is required, first make sure the

wheels are straight forward and insert the

steering arm spacer over the center nut. Refer

to “Steering System - Alignment” Service

Information Sheets for more detail.

3. Insert a 1/4 in. dowel pin through the center

hole on the speed control assembly to lock the

speed control assembly in place. The dowel

should be pushed through the hole far enough

to hold both slide assemblies in place.

4. Loosen the jam nut on the cable and lengthen or

shorted the cable as needed.

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды