Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 131 / 142

ELECTRICAL

7-14

Toro TimeCutter SW/SWX Service Manual

PTO Circuit & Operation

- The PTO clutch is powered by the Push/Pull PTO

switch.

- The PTO clutch is grounded through the Brake

Actuator Module.

- The PTO Clutch will only engage when:

• The ignition key switch is in the ON position

(engine running or not).

• The PTO switch is in the ON position sending

battery voltage to the PTO clutch.

• The PTO switch is in the ON position removing

battery voltage to the Brake Actuator Module (pin

8).

• Proper battery voltage is present at the key switch

and brake control module.

• Proper ground is present at the battery, chassis

and brake control module.

• An operator is in the seat and the seat switch is

closed supplying battery voltage to the module

(pin 7).

Note: The engine will not crank over to start when

the PTO switch is ON (Fig. 172).

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды