Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 27 / 142

CHASSIS

3-4

Toro TimeCutter SW/SWX Service Manual

Pod / Fender / Fuel Tank Service

Pod / Fender Removal – RH

1. Raise seat and disconnect battery terminals.

2. Remove the (3) screws (A) securing control panel to

RH fender (B). Move control panel inward towards

the center of the unit.

3. Remove the (3) screws (C) securing the RH fender

to frame.

4. Maneuver RH fender (B) up and off frame.

Note: The RH control lever and deck lift lever must

pass through the RH fender during removal

and installation.

Pod / Fender Installation – RH

1. Maneuver RH fender (B) into position.

Note: The RH control lever and deck lift lever must

pass through the RH fender during removal

and installation.

2. Install the (3) screws (C) that secure the RH fender

to frame and torque the (3) screws to specification –

7 ft-lbs. (9 Nm).

3. Position control panel back onto RH fender. Install

and sufficiently tighten the (3) screws (A) that secure

the control panel to the RH fender (B).

4. Verify choke cable, throttle cable and wiring are

properly routed.

5. Connect battery terminals and lower seat.

(Fig. 010)

Fig. 010

PICT-1040

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды