Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 69 / 142

HYDROSTATIC DRIVE SYSTEM

5-4

Toro TimeCutter SW/SWX Service Manual

5. Accelerate the engine to full RPM. Observe the

rear

tire’s forward or reverse movement. If the

tire is creeping in forward or reverse, a neutral

adjustment is needed. Make sure the traction

pedal is in the neutral position.

6. When in neutral, the stud should be in the center

of the slot in the control arm (A).

7. If one wheel is creeping, set the neutral on

BOTH drives. Set both wheels so they are

slightly rotating forward. Turn the adjustment

nut (B) clockwise or counter-clockwise until

creeping stops. Then turn it another 1/4 turn in

the same direction.

8. When neutral is achieved, have the person

sitting in the seat push the traction lever full

forward. Count the number of revolutions of the

tire pera specified amount of time (example: 10

seconds). Record the number of revolutions.

Repeat for opposite side.

9. Compare the number of revolutions for each tire.

If they are within 2-3 RPM of each other, the

tracking is set correctly. If they are not within

that spec, slow down the faster hydro by turning

the adjustment nut counter-clockwise 1/4 turn

and retest. Continue to adjust the hydro this

way until the revolutions are with the spec.

10. Turn the engine OFF.
11. Safely lower unit.

12. If the unit is set correctly it should drive straight

on level ground with the wheels going straight

forward and WITHOUT having to “steer” the unit

straight.

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды