Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 51 / 142

CHASSIS

3-28

Toro TimeCutter SW/SWX Service Manual

6. Remove the speed control assembly from the

unit.

Speed Control Assembly Installation

1. Insert the speed control assembly to the chassis.

The bearing pivot (A) needs to be oriented

so the flats of the pivot fit into the hole in the

chassis. Insert bolt and torque bolt to 45-55 ft-

lbs. (62-76 Nm).

2. Insert a 1/4 in. pin through the hole on the pedal

mount and into the foot pedal assembly. This

ensures the foot pedal is in the neutral position.

3. When a pin is inserted into the pedal mount,

the holes on the left side of the speed control

assembly should line up. Place a 1/4 in. dowel

in one of the alignment holes and into the

chassis on the speed control assembly to keep

it in position.

SPEED CONTROL ASSEMBLY - ZERO TURN TRACTOR

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды