Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 29 / 142

CHASSIS

3-6

Toro TimeCutter SW/SWX Service Manual

Fuel Tank Removal

1. Remove LH fender as shown in this chapter.

2. Disconnect and properly secure the (2) fuel / vent

lines from the top of fuel tank assembly (G).

(Fig. 013)

Fuel Tank Installation

1. Position fuel tank assembly (G) into the frame slots.

2. Install the (2) fuel tank retaining springs (H) to

secure fuel tank to the frame.

3. Properly connect the (2) fuel / vent lines.

4. Install LH fender as shown in this chapter.

5. Verify proper installation of the fuel tank and fuel /

vent lines.

(Fig. 015)

Fig. 013

PICT-1054

Fig. 015

PICT-1041

3. Remove the (2) fuel tank retaining springs (H) by

pulling them outward (Fig. 014).

Fig. 014

PICT-1042

4. The fuel tank is now loose and can be removed

vertically from the frame.

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды