Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 10 / 142

SAFETY INFORMATION

1-1

Toro TimeCutter SW/SWX Service Manual

This symbol means WARNING or PER -

SONAL SAFETY INSTRUCTION – read

the instruction because it has to do with

your safety. Failure to comply with the

instruction may result in personal injury

or even death.

This manual is intended as a service and repair manual

only. The safety instructions provided herein are for

troubleshooting, service, and repair of the TimeCutter®

SW, the TimeCutter® SWX zero radius turn mowers.

General Information

Think Safety First

Avoid unexpected starting of engine…

Always turn off the engine and disconnect the spark plug

wire(s) before cleaning, adjusting, or repair.

Avoid lacerations and amputations…

Stay clear of all moving parts whenever the engine is

running. Treat all normally moving parts as if they were

moving whenever the engine is running or has the

potential to start.

Avoid burns…

Do not touch the engine, muffler, or other components,

which may increase in temperature during operation,

while the unit is running or shortly after it has been

running.

Avoid fires and explosions…

Avoid spilling fuel and never smoke while working with

any type of fuel or lubricant. Wipe up any spilled fuel

or oil immediately. Never remove the fuel cap or add

fuel when the engine is running. Always use approved,

labeled containers for storing or transporting fuel and

lubricants.

Avoid asphyxiation…

Never operate an engine in a confined area without

proper ventilation.

Avoid injury from batteries…

Battery acid is poisonous and can cause burns. Avoid

contact with skin, eyes and clothing. Battery gases can

explode. Keep cigarettes, sparks and flames away from

the battery.

Avoid injury due to inferior parts…

Use only original equipment parts to ensure that

important safety criteria are met.

Avoid injury to bystanders…

Always clear the area of bystanders before starting or

testing powered equipment.

Avoid injury due to projectiles…

Always clear the area of sticks, rocks or any other debris

that could be picked up and thrown by the powered

equipment.

Avoid modifications…

Never alter or modify any part unless it is a factory

approved procedure.

Avoid unsafe operation…

Always test the safety interlock system after making

adjustments or repairs on the machine. Refer to the

Electrical section in this manual for more information.

The TimeCutter SW, and TimeCutter SWX

operator’s manuals contain safety information and

operating tips for safe operating practices. Operator’s

manuals are available online through your Toro parts

source or:

The Toro Company

Publications Department

8111 Lyndale Avenue South

Bloomington, MN 55420

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды